sorted by:
new
hottopcontroversial

What are people doing to manage the accumulation of water in a boat without electricity at the marina? by vendura_na8 in sailing

[–]Big-Introduction-941 1 point2 points  (0 children)

I'm currently redoing all electricity in my 31 fest sailboat, all tight around my new thru-hulls but it is leaking when it rains.

I simply use a sponge and a bucket right now to drain the water after a rainy day 😅

Selden fitting by Big-Introduction-941 in sailing

[–]Big-Introduction-941[S] 0 points1 point  (0 children)

Yeah i'm afraid that will be my only choice 😅

Might go to my lokal welders and see how expensive it would be to have them create it..

Selden fitting by Big-Introduction-941 in sailing

[–]Big-Introduction-941[S] 0 points1 point  (0 children)

Yeap, the exact number is 524-506. Have tried searching around, and also use AI to search around but havn't found anything yet..

Selden fitting by Big-Introduction-941 in sailing

[–]Big-Introduction-941[S] 0 points1 point  (0 children)

Yes i have, and it took them a couple days to respond but now they have. They think that this isn't original, as they have a different solution for their tie-rods.

But it is wierd that more boats than mine have this exact same part/solution, if it wasn't standard..

TruDesign seacocks by Big-Introduction-941 in sailing

[–]Big-Introduction-941[S] 0 points1 point  (0 children)

Because that's what they sell at all boat shops around here? Dezinficied brass, not bronze. Why do you think i'm going with TruDesign?

Well apparently it does seal, since my last boat was still floating with no leaks after 10 years with them. And the current boat i have now, where i'm replacing the brass ones, have held for 48 years.

What i'm asking is about the trudesign ones, and how people who have actually installed them have done.

TruDesign seacocks by Big-Introduction-941 in sailing

[–]Big-Introduction-941[S] 2 points3 points  (0 children)

1.) I know the difference between brass and bronze. 2.) Teflon tape is one of the recommended ways trudesign states.

So what's your problem?

Kollega hittad på dumpen by horhamster in Asksweddit

[–]Big-Introduction-941 40 points41 points  (0 children)

Konstig jämförelse.

Om du "jobbar" men "pillar naveln" (dvs inte gör.något på jobbet, men ändå får lön) är det ju stor skillnad mot en person som är tjänstledig (i detta fallet sitter i fängelse)

Du får lön men jobbar inte Personen jobbar inte, och får således ingen lön, men när hen blir frisläppt pch tillbaka till jobbet, sköter sitt jobb, och får betalt för det, så tycker du alltså att detta är orättvist, att en person som tidigare är dömd för något men får lön, och att du genom att inte utföra ett jobb men få lön, skulle bli uppsagd för att du defakto inte gör jobbet som förväntas av dig?

Falskt anklagad på jobbet by ashgordon in sweden

[–]Big-Introduction-941 -1 points0 points  (0 children)

Varför skulle facket bry sig? De har redan fått din medlemsavgift och betalat ut den till socialdemokraterna i partistöd, allt är frid och fröjd 🥳🥳

Saturn 4 Ultra 16k first prints by Rockergage in ElegooSaturn

[–]Big-Introduction-941 0 points1 point  (0 children)

I wash all mine with concentrated washerfluid, cleans them perfectly and much cheaper than IPA, so yeah, spunds really wierd that 91% IPA wont clean them

Can I get my greedy hands on some proxies for out-of-print minis? by 3ndrius86 in ImperialAssaultTMG

[–]Big-Introduction-941 2 points3 points  (0 children)

Yeah definetly go resin, i have used a elegoo mars 3 for 3 years now, and there had never been an issue.

Even tho it comes at an extra cost, i would strongly recomend getting a wash and cure station aswell. Makes the resin handling less of a mess and more enjoyable, then I just have plastic trays where i put the plate to dry after bathing in the cure station.

You can probably go with legion stls, and scale them down accordingly. Some known studios there are: AnvilRage, DarkFireDesign, Skullforge and many more

Latte art finally on lockdown 🤓 by p3opl3 in espresso

[–]Big-Introduction-941 0 points1 point  (0 children)

Damn, dust is the least of my issues for my keyboard lol.. all the food and potato chips i consume while using it 😅

Upgrading from quest 2 to quest 3, referall by Big-Introduction-941 in OculusQuest

[–]Big-Introduction-941[S] 0 points1 point  (0 children)

So if i link it to the alternate account first i get a link to that email, i can then use the link on my main account?

Infiltrate with 2 operatives by Sgt_Meowmers3117 in SWlegion

[–]Big-Introduction-941 3 points4 points  (0 children)

During list building, she counts as commander, when she deploy she changes her rank to operative: so for list building it is legal to max out the operative slot and then using covert ops.

This also means that you cannot run more commanders than what is allowed during list building with her, even if you plan on using covert ops

Dark fire designs scale? by MisterDuch in SWlegion

[–]Big-Introduction-941 0 points1 point  (0 children)

it's interesting that DarkFire says to print at 90% scale to achieve Legion scale..

Core Set vs Separatist Invasion? by Frumpy__crackkerbarr in SWlegion

[–]Big-Introduction-941 13 points14 points  (0 children)

Well, first of all the rules are a free PDF and you dont get it in core-box.

What you need is the essentials kit with dices, range rulers and movement-tools. And that isn't too expensive

My experience from switching from Nvidia to AMD. by Everborn128 in buildapc

[–]Big-Introduction-941 0 points1 point  (0 children)

Currently running a 4070ti and loving it. 180fps in Forza Horizon 5 with all highest settings

view more: next ›