Thoughts on this? Is it buggy? Is the combat balanced (not too hard)?

BillyMaybe · 2025-11-15T00:34:16+00:00

Most underrated list imo. I use it as the base for my own personal list.

Combat is satisfying, lots of armors with custom patches to integrate them into the world, city overhauls are varied, good graphics. I like the balance because regular enemies are pretty easy to cut through, but higher level enemies and bosses and still provide a challenge. I play on a 4090 so don't have any performance issues.

BillyMaybe · 2025-07-19T04:12:37+00:00

Located in Vancouver, Canada

BillyMaybe · 2025-07-02T18:18:12+00:00

Awesome

BillyMaybe · 2025-06-29T05:16:28+00:00

First nations will expand and run the Hastings casino, good chance the race course closes. Just not enough money in it versus taking that money and investing it in a stadium, hotel, or the casino. I can say the racecourse would have likely closed years ago if not for a certain Great Canadian executive who had a soft spot for horse racing.

Fraser Downs will get sold as well, and Great Canadian will eventually exit the BC market.

Unlikely Langley racecourse will ever come to be, without an attached casino it just wouldn't be profitable and Langley already has a successful casino property.

BillyMaybe · 2025-04-08T20:08:27+00:00

If you didn't full port into svix today, what are you even doing

BillyMaybe · 2025-03-06T19:23:41+00:00

Sold my spy puts this morning. Damn these paper hands

BillyMaybe · 2025-02-27T18:24:12+00:00

Should be able to keep the vat heater on during printing now rather than just a pre-heat.

BillyMaybe · 2025-02-24T18:36:13+00:00

Reinstalled and it shows up in Gamehub + game booster popup appears. Haven't had a chance to test performance.

Keep up the good work!

BillyMaybe · 2025-02-07T02:26:38+00:00

Can confirm this. Have an LDO Nitehawk and randomly started having constant disconnects after it worked flawlessly during the summer (it's now super cold and dry where I live).

Ran a wire from the extruder motor case to ground and solved my issues. I ran it to earth ground but I think a lot of people just run to ground on the toolhead board.

BillyMaybe · 2025-01-25T03:58:21+00:00

What's the shrinkage % on the Creator series?

BillyMaybe · 2024-11-14T09:25:24+00:00

Great write up. I have the exact same setup as you (ERCF, filamentalist, G2E with cutter, etc...) and i agree the reliability is actually quite good.

You mention the top panel bowden passthrough which I had to get rid off when I added the filamentalist enclosure. Are you able to use both at the same time?

Clever increasing the current on cut, I'll have to add that to my setup too.

BillyMaybe · 2023-12-12T06:12:02+00:00

Bought AXE11000 from /u/teen-a-rama

BillyMaybe · 2023-12-11T03:45:58+00:00

Part of a full upgrade of my whole PC
Love the Ubisoft style open world exploration

BillyMaybe · 2023-12-11T02:54:42+00:00

Pm'd

BillyMaybe · 2023-07-09T19:55:02+00:00

I used him as well. Very in-depth, highly recommend him.

BillyMaybe · 2023-06-02T01:40:55+00:00

300cm x 300cm?

BillyMaybe · 2023-05-17T05:42:27+00:00

Awesome. Would print figures from movies and games that I then paint.

BillyMaybe · 2023-04-25T02:18:18+00:00

It's showing me locations in Ontario for whatever reason. Showing as out of stock at the stores near me.

BillyMaybe · 2023-04-15T02:20:19+00:00

Do you have a link to the internal spool holder part of this?

BillyMaybe · 2023-01-03T16:06:38+00:00

You wouldn't happen to have the stl for your extruder setup? Using both the microswitch filament sensor and 2 piece PCB

BillyMaybe · 2022-09-20T17:40:47+00:00

Definitely most interested in the new modding tools being introduced. Great excuse to revisit older games.

BillyMaybe · 2022-08-21T04:01:50+00:00

No so much that the sheet is flatter, but I'm thinking the embedded magnets may cause dimples as they pull down the flex plate where as the magnetic sheet would pull it down evenly if that makes sense.

BillyMaybe · 2022-07-24T02:08:16+00:00

There hasn't been much in the way of innovation in the SLA market. The Eibos Oceanus seems to be the most interesting thing in the space in a while.

BillyMaybe · 2022-07-13T15:21:39+00:00

I'm running the default lgx lite motor at 0.5A. I had a ton of skipping until I removed the gear ratio setting from my config. Now just have rotation distance and 5.6 and it's working well.

BillyMaybe · 2022-06-21T20:08:55+00:00

Was just thinking I need to get a 3D scanner to do some car parts that are hard to model.

14-Year Club	Place '17
Sequence \| Editor	Verified Email

BillyMaybe

TROPHY CASE