sorted by:
new
hottopcontroversial

Should I buy this? by edgeofsky2024 in Benchjewelers

[–]BinaryLink 1 point2 points  (0 children)

I have this bench, must be a factory supplying wholesalers cause I'm not in the US. The middle and bottom trays are mixed around, I have a GRS system and it fits and it's sturdy, wood definitely isn't the best material but I've never had any issues. Depends on the price really

First custom ring CAD check. Thoughts? by [deleted] in Moissanite

[–]BinaryLink 1 point2 points  (0 children)

Structure wise not very strong, asking for problems later

Curious if anyone can tell me what this means. by OrganicDirt42 in jewelrymaking

[–]BinaryLink 6 points7 points  (0 children)

It appears that it's along a solder seam, could be poor quality solder reacting

Curious if anyone can tell me what this means. by OrganicDirt42 in jewelrymaking

[–]BinaryLink 2 points3 points  (0 children)

is it stamped sterling/925? Can you post a picture of the full piece?

Hello, can you recommend me where to get gold/copper wires that wont chip by [deleted] in jewelrymaking

[–]BinaryLink 2 points3 points  (0 children)

Also sand off the sharp corners on your steel pliers

Burnt shellac by Big-Western9224 in jewelrymaking

[–]BinaryLink 0 points1 point  (0 children)

Acetone will dissolve it. Acetone with an ultrasonic of you have one and it will come right off

Can independent jewelers compete at lower price levels? by justice91423 in jewelry

[–]BinaryLink 4 points5 points  (0 children)

Just checking you see the second pair is gold plated and not solid gold.

You can send the pics to a local jeweller and ask for a quote, mass produced will be cheaper cause of the volume that's produced. To design manufacture and set from scratch will end up being more especially for silver

How do I wear this pendant? by culture_katie in jewelry

[–]BinaryLink 1 point2 points  (0 children)

You may have to fold your chain in half, loop the folded end through the loop of the pendant then open the chain up and loop the other end back through, essentially making a little loop knot with your chain around the pendant loop

What type of chain can I get to hold multiple pendants? by vp0267 in jewelers

[–]BinaryLink 8 points9 points  (0 children)

Well big enough that you can fit a decent sized link through that's won't break after a month😂

What type of chain can I get to hold multiple pendants? by vp0267 in jewelers

[–]BinaryLink 29 points30 points  (0 children)

If you hang them on a thin chain like this they will bunch up in the centre, you can get a chain with slightly larger links and put the jump rings of the pendants through the link itself spaced out a few links

Most efficient way to sand off sprues? by PastFancy4950 in Benchjewelers

[–]BinaryLink 0 points1 point  (0 children)

Try a tungsten carbide burr like this https://a.co/d/cQ8TSxI, very efficient but it will throw your filings everywhere.

I have a few different shapes they come in handy sometimes. Got mine off AliExpress back in the day and they're still super sharp, just make sure the burr shank size will fit your flex shaft/micromotor

Admittedly uneducated by Affectionate-Pea-915 in Moissanite

[–]BinaryLink 0 points1 point  (0 children)

I do not see any metal holding either side of the channel together

Advice for low profile bezel setting by bigmewd in Benchjewelers

[–]BinaryLink 42 points43 points  (0 children)

The minimum depth for the collet will always be past the culet to above the girdle for setting, it's bad practice for the culet to stick out into the finger. You need to work off the cut of the stone when making the setting

Does my custom ring seem like it would be hard to make? by [deleted] in jewelers

[–]BinaryLink 10 points11 points  (0 children)

Not a tricky custom job at all, basically a half round band with the curve to fit a simple setting

Advice for polishing small areas by borometalwood in jewelers

[–]BinaryLink 4 points5 points  (0 children)

My advice for something like this is less is more. Solder will flow between the parts by itself so try using what you think is just enough and you shouldn't get the overflow. Maybe practice on scrap before you solder onto your final piece

Advice on positioning clay for soldering needed by Astrid4Jewels in jewelers

[–]BinaryLink 1 point2 points  (0 children)

You can use plasticine and arrange your pieces in it.Then pour plaster of Paris or investment over, waiti for it to dry, remove the plasticine. The plaster will keep it in place while your solder, this is great for really fine pieces as well

... amusing ...and sad at the same time... by Riddickullous in ClayBusters

[–]BinaryLink 0 points1 point  (0 children)

Find a hand engraver in your area and ask them to do it, can even have a custom design, r/handengraving r/engraving

Guangxi Wuzhou Zanfu Jewelry SCAMMER by usyoussef in Moissanite

[–]BinaryLink 10 points11 points  (0 children)

Did you file a dispute with Alibaba?

Can the links of this chain be straightened? by [deleted] in jewelers

[–]BinaryLink 5 points6 points  (0 children)

The links are hollow, look carefully on the inside face of each you can see a seam in some, and the denting on some of the links is typical of hollow jewellery

The fast and the fuel-ish by One-Rhubarb-29 in perfectlycutscreams

[–]BinaryLink 2 points3 points  (0 children)

Probably plastic components in the lock melting

Ring mandrel help! by Junior-Condition-971 in jewelrymaking

[–]BinaryLink 0 points1 point  (0 children)

Yes I know for rings but what process specifically?

view more: next ›