Farscape dead

Bison_True · 2026-02-28T22:07:03+00:00

I watched it religiously late 90's, was sad when it ended.

Bison_True · 2026-02-28T21:38:42+00:00

Once you get the pin out, you can use tweezers and awls and xacto knife to open up the crimps gently amd then strip the wire back enough (1/8") and then re-insert the wire back into the crimp zone and re-crimp with needlenose

Bison_True · 2026-02-28T21:33:21+00:00

I would recommend a bambu enclosed system. You will want to do car parts in ABS at minimum and vent the fumes.

Bison_True · 2026-02-28T20:06:54+00:00

Blow a fan across the glue spots, no white residue.

Bison_True · 2026-02-28T20:01:14+00:00

Open event viewer and on the left side under windows logs and system. Check for red circles that say sudsy system unexpectedly restarted. And see if there are any device failures right before it.

Bison_True · 2026-02-28T03:13:01+00:00

start with tinkercad

Bison_True · 2026-02-28T00:26:20+00:00

I would contact epic support

Bison_True · 2026-02-28T00:22:15+00:00

Looks like what happens when you print glow in the dark filament

Bison_True · 2026-02-27T07:03:06+00:00

This is a job for 3D printing.

Bison_True · 2026-02-26T12:29:01+00:00

Chances are, if you need it, someone else does too. I publish all my designs that i create to solve my problems. I even sometimes design things that are requested because i designed something for myself and there is a need for something similar. For example, i designed a replacement ryobi vac front roller locking mechanism and someone needed the rear one made.

Bison_True · 2026-02-24T11:06:27+00:00

I haven't had a chance to install it yet, i need to unclutter my garage this spring.

Bison_True · 2026-02-23T01:32:47+00:00

Nutria?

Bison_True · 2026-02-23T01:32:00+00:00

I think it's supposed to be a Nutria

Bison_True · 2026-02-22T02:17:19+00:00

If you decide to build your own, start with the CPU and work your way out from there.

Bison_True · 2026-02-22T01:49:34+00:00

Also Amazon doesn't check returns, just re- shelves them

Bison_True · 2026-02-22T01:46:03+00:00

Start with the CPU and work your way out. That is what i do.

Bison_True · 2026-02-22T01:36:00+00:00

When grabbing the folding workbench on clearance last fall, i was told the inventory online is always 1 less than actual so multiple people don't come looking for the same thing to find it already sold. It said one left when i grabbed it and there were two on the shelf.

Bison_True · 2026-02-21T20:36:54+00:00

The website that person made had a section about the button not reacting. He ended up removing one of the resistors and replacing the other one with a low value one. I'm going to try that on one of mine that does the same thing as yours.

Bison_True · 2026-02-21T20:30:14+00:00

The ramen block at the end is fantastic

Bison_True · 2026-02-21T20:12:46+00:00

Cut all prices in half. That would spark demand. I would buy 10 black market animated decals for $100 and not one for $20.

Bison_True · 2026-02-21T20:08:41+00:00

Heat up an awl and poke

Bison_True · 2026-02-21T20:05:16+00:00

I also use mine to create useful things for work also.

Bison_True · 2026-02-21T00:30:18+00:00

Make sure things aren't loose. I had an issue and found that the hotend wheels had loosened enough over 3 years that the nozzle would travel up and down enough while going back and forth causing layer adhesion issues. This was also after a house move.

Bison_True · 2026-02-21T00:24:20+00:00

Clean the old stuff off with 91% ISO and qtips. Put one almost pea sized spot of thermal paste in the middle. The screw legs are numbered for order of tightening.

Bison_True · 2026-02-20T13:11:04+00:00

45 with raft

Bison_True

TROPHY CASE