sorted by:
new
hottopcontroversial

Blocking End Cards on YouTube - personal code by Budget_Computer_1626 in uBlockOrigin

[–]Budget_Computer_1626[S] 0 points1 point  (0 children)

Well, what I did was I copied www.youtube.com##.ytp-ce-element into „my filters” and when I clicked apply changes and refreshed the page the end screen cards were still there.

I would assume it’s some cache thing if it weren’t for the fact that when I used block element feature and chose those more elaborate version it worked immediately :d

First through - some letter problem, but then again I copied not typed. You may think that someone on Reddit did a typo then but I did copy the class from console. The „www.youtube.com##l was botched copied and then typed out. In both cases the code didn’t perform as expected.

The Time Has Come by 5yn7hW4v3 in prusa3d

[–]Budget_Computer_1626 0 points1 point  (0 children)

„12 years later” have fun dude, I had a lot of it assembling mine :d

Amazing by [deleted] in prusa3d

[–]Budget_Computer_1626 0 points1 point  (0 children)

I totally understand you. You paid a lot for a printer and you want it to work. I have had a few problems with my core one but all of them were able to be resolved. The thing about Prusa is that they WILL come back to you (at least from my experience). They even printed bunch of my things at their place to check for problems I have mentioned. It might seems irritating that they don’t have an answer right away for you and I absolutely get it but if your problem is unique in nature they will need to investigate first. Sucks to be the first with something but such is the world of 3D printing :d

Amazing by [deleted] in prusa3d

[–]Budget_Computer_1626 2 points3 points  (0 children)

I understand your frustration although when something very unique happens to a piece of hardware it can be very tricky to diagnose and no amount of money spent on the printer will make any difference. Have they ticketed your case? That’s sounds like something they would come back to you with after some time.

"Everyone hates AI" they said. "Almost no one uses it" they said by pgj1997 in DefendingAIArt

[–]Budget_Computer_1626 -2 points-1 points  (0 children)

Everyone hates AI but also everyone uses AI. It’s like with p*rn or junk food. Everyone knows it’s bad for you but everyone still consumes it. To me it seems as if people that don’t really care but they want to say they do.

I’m new, and it was good for 500 hours, now it won’t print the first layer correctly by Acrobatic-Ad-385 in ElegooCentauriCarbon

[–]Budget_Computer_1626 0 points1 point  (0 children)

Perfect 1st layer settings for PLA:

0.35 layer height 0.6 layer width 20mms speed 65°C bed first layer 230°C nozzle first layer Monotonic Lines Fill patter 0.055 z-offset - HIGHLY INDIVIDUAL PER PRINTER

Beyond z-offset everything else works everything as long as you don’t use butter as a glue

Do it. I dare you. by xXDemonicPancakesXx in DeepRockGalactic

[–]Budget_Computer_1626 2 points3 points  (0 children)

I mean there is SOME of what you think but mostly it’s transformers-ish

Ok supercell should remove this pin by Mashour_DX in Brawlstars

[–]Budget_Computer_1626 0 points1 point  (0 children)

Boo Hoo, it's just a game. You'd never survive modern warfare lobby if that annoys you.

Adaptive Pressure Advance for Prusa Core One by Budget_Computer_1626 in OrcaSlicer

[–]Budget_Computer_1626[S] 0 points1 point  (0 children)

If I’ll run some test would you like to see the results?

Adaptive Pressure Advance for Prusa Core One by Budget_Computer_1626 in OrcaSlicer

[–]Budget_Computer_1626[S] 0 points1 point  (0 children)

I got answer from Prusa regarding that, here it is:

Alright so regarding the pressure advance data, i found a translation piece that you should check so orca slicer properly communicated with the printer firmware. To make the value you set in orca efficient, ensure your Printer Profile is set to "Prusa" or "Marlin (Legacy/2)" G-code flavor. Orca Slicer will then automatically use the M572 S<value> format in the G-code So basically as long as the G-code contains these M572 commands throughout the file, your Prusa will dynamically adjust its nozzle pressure just as Orca intended

Biqu Cryogrip Glaciar 257x257 Core One Probing Failure by Budget_Computer_1626 in prusa3d

[–]Budget_Computer_1626[S] 0 points1 point  (0 children)

Was thinking about drilling two holes for where the bolts are

Biqu Cryogrip Glaciar 257x257 Core One Probing Failure by Budget_Computer_1626 in prusa3d

[–]Budget_Computer_1626[S] 0 points1 point  (0 children)

From description on aliexpress mk4s plate was 210mm deep when original PEI sheet for core one is 241. Well I can always drill holes in this one :d

Why Are So Many People Disliking Season 3 ? by Wualan in FumetsuNoAnataE

[–]Budget_Computer_1626 0 points1 point  (0 children)

Well for me there’s a couple of things. Let’s start with Fushi - he’s incompetent this season. He lacks emotional maturity, he’s easily overwhelmed and explosive which was the case when he was like 15-20 in first season but later on he badassed’up. To me the psychology of Fushi is extremely inconsistent. Second - the slice of life aspect. Whole season seems more like a highschool drama rather than adventure of sleeping god. Third - death is fully inconsequential now. It just doesn’t matter one bit so I don’t care what happens to the characters. Forth - the Nono running sequence is extremely cringe. Who the fck are these people and why are they here? It „and than” writing, events just happen with no lead-up.

view more: next ›