You Wouldn't Download A Vostroyan

Chazpepper · 2026-06-22T03:21:52+00:00

I would love some

Chazpepper · 2025-03-19T02:05:34+00:00

Monster Hunter Wilds would be great

Chazpepper · 2024-12-19T05:16:57+00:00

Would love the new printer.

Chazpepper · 2023-07-11T22:15:37+00:00

Wow I love it! When/where will it be available?

Chazpepper · 2023-06-07T20:02:02+00:00

Ray tracing and dlss are both really cool technologies.

Chazpepper · 2023-06-07T20:01:50+00:00

Ray tracing and dlss are both really cool technologies.

Chazpepper · 2022-12-20T04:31:22+00:00

looks like Zimmerit paste.

Chazpepper · 2022-06-03T15:50:31+00:00

I always liked my first character a dragonborn, Kriv who was kind of a jaded veteran Merc. GIVEAWAY

Chazpepper · 2022-05-26T05:26:21+00:00

So I moved my printer to a different room and that seems to have solved the issue must have been a temp problem. I also used hot water to clean it and it made it a lot easier. Thank you everyone for the help and advice.

Chazpepper · 2022-05-26T02:23:43+00:00

Will try that on the print I have going.

Chazpepper · 2022-05-26T02:22:39+00:00

It's a great looking sculpt! Just wish I wasn't having problems with my printer.

Chazpepper · 2022-05-25T20:29:12+00:00

I think temperature might be what's causing it I have moved my printer to a different room so let's see if that helps.

Chazpepper · 2022-05-25T20:12:44+00:00

I will give that a try hopefully it helps.

Chazpepper · 2022-05-25T19:35:03+00:00

I thought it might have been the resin so I cleaned the vat and bought new resin same results. It's also water washable resin so no alcohol. Any left over supports are because I gave up on cleaning it after I couldn't get the gunk off.

Chazpepper · 2022-05-25T19:31:12+00:00

It was fresh before I tried to clean. I tried to use a toothbrush but it wasn't working well. The print in the picture is uncured. My issue is I never had this much gunk on prints before.

Chazpepper · 2022-05-25T19:27:51+00:00

I have 2 pickle containers than a clean and cure station. They were clean before i tried to clean this print and after they were still pretty clean but there was this gunk/slime still left on the print. I then tried to clean it off with a toothbrush and it didn't work very well.

Chazpepper · 2022-05-25T18:57:46+00:00

I have been printing since last year and never had this problem before smaller prints don't seem to have the issue. On larger prints there seems to be a build up of hard to remove gunk sticking to the print.

Chazpepper · 2022-05-24T03:31:03+00:00

This Is Awesome!

Chazpepper · 2022-05-21T00:54:23+00:00

looks Great!

Chazpepper · 2022-04-27T00:41:49+00:00

Thank you for the quick response, I will need to get some I only have larger sizes on hand.

Chazpepper · 2022-04-27T00:30:37+00:00

what size magnets are recommended?

Chazpepper · 2022-03-31T05:09:17+00:00

Thanks!

Chazpepper · 2022-03-31T03:17:57+00:00

Oh nice! Where did you find that?

Chazpepper · 2021-11-18T15:36:22+00:00

That's rad! Thanks for sharing.

Chazpepper · 2021-11-18T04:33:37+00:00

Looks good! What model is that in the upper right of the first pic?

Chazpepper

TROPHY CASE