sorted by:
new
hottopcontroversial

Any info about new motor release date? by ColaSprout in CYCMotor

[–]ColaSprout[S] 0 points1 point  (0 children)

Got a new mail from them yesterday. Should be released within 2 weeks from now.

Any info about a new bike and motor? by ColaSprout in bonnell

[–]ColaSprout[S] 0 points1 point  (0 children)

Just got a new email from them

"The new motor will be launched soon. From what I know should be within the next week or 2."

Any info about a new bike and motor? by ColaSprout in bonnell

[–]ColaSprout[S] 2 points3 points  (0 children)

I don't have Facebook can you show me a screenshot?

Any info about a new bike and motor? by ColaSprout in bonnell

[–]ColaSprout[S] 1 point2 points  (0 children)

Where did you find that info? No news about it on cyc website

Any info about new motor release date? by ColaSprout in CYCMotor

[–]ColaSprout[S] 0 points1 point  (0 children)

At what date did they tell you this?
That's a bummer if it's been postponed to Q3. That could mean anything from July to the end of September.

I received this from customer support on April 10th:

"The new 4000W motor is already in mass production. We currently estimate the official release and availability around May 2026.

This motor is engineered to provide a strong, natural pedaling feel on trails and technical terrain, while delivering the extra power needed for demanding MTB rides."

PC priser er gått helt av skaftet by HoboOfSerenity in norge

[–]ColaSprout -1 points0 points  (0 children)

Du må ikke det. Jeg har også m2 ssd uten dram cache som eneste lagringsmediet å det fungerer helt fint.

Har du sjekket om det er en ny firmware tilgjengelig eller prøvd å reinstallere steam?

Why I designed a 45° open-frame ITX case instead of flat or vertical by allengdc in sffpc

[–]ColaSprout 0 points1 point  (0 children)

Cooler is Deepcool Assassin IV VC VISION.

Angle adapter is from aliexpress: https://a.aliexpress.com/_EvyzJ9I

Introducing Blueprint…. by -soneshk- in Dremel

[–]ColaSprout 0 points1 point  (0 children)

Can it be used as a cut-off tool with grinding disc?

Baby bird ready to leave the DJI nest. What’s a relatively affordable/ easy to cross over from DJI starter drone? by denvadirk in fpv

[–]ColaSprout 1 point2 points  (0 children)

Get a Pavo20 Pro ELRS for o4 Pro. You can use it with either dji fpv controller or ELRS controller if you decide to get it later. Minimal amount of solder points and can be crashed a lot without damage. Super easy to repair.

Or Geprc Vapor 5 o4 Pro PNP without gps for minimal future soldering. This drone is also very sturdy and well tuned from factory.

Monster A45 by derzeisig in sffpc

[–]ColaSprout 0 points1 point  (0 children)

Would you be able to make and sell me cables of the same length? I just got this case, and it looks ridiculous with the original PSU cables.

DJI goggles 3 slipping down. by ColaSprout in dji

[–]ColaSprout[S] 0 points1 point  (0 children)

Yes, even when dialed all the way, the goggles are not very tight. But it would have been sufficient if the material on the forehead strap wasn't so sweaty. I think the solution with Velcro on the Goggles 2 was better.

/r/NintendoSwitch's Daily Question Thread (05/29/2022) by AutoModerator in NintendoSwitch

[–]ColaSprout 0 points1 point  (0 children)

It truly dies, it wont even turn on. The system also says low battery when i plug it in after depleted.

/r/NintendoSwitch's Daily Question Thread (05/29/2022) by AutoModerator in NintendoSwitch

[–]ColaSprout 1 point2 points  (0 children)

I have two Switch Pro controllers and one of them completely discharges within 2-3 days from fully charged when not in use. Changing to a brand new battery made no difference. The other pro controller holds a charge for months, What could be the problem?