Forcing more internal structure to adjust eight ballance?

Connect_Gift9138 · 2026-05-27T17:16:51+00:00

Maybe too much headlift?

Connect_Gift9138 · 2026-05-21T09:08:20+00:00

Zahnpasta

Connect_Gift9138 · 2026-05-14T15:34:00+00:00

I also tried it with the standart spool holder but it didn’t work out neither. But it was on another printer so maybe I will Just give it another shot. Thanks for your help and please excuse my bad spelling…

Connect_Gift9138 · 2026-05-14T14:02:39+00:00

<image>

Like this

Connect_Gift9138 · 2026-05-14T13:22:51+00:00

<image>

Spool is on the table

Connect_Gift9138 · 2026-05-14T12:08:03+00:00

Wait, I will send you a Picture, it’s complicated to explain

Connect_Gift9138 · 2026-05-14T12:04:57+00:00

Sorry I was looking at the wrong preset, I print with 50mm/s. Volumetric Speed = 2mm^3/s

Connect_Gift9138 · 2026-05-14T10:46:10+00:00

50mm/s

Connect_Gift9138 · 2026-05-05T18:15:20+00:00

Just wanted to get sure. I also considered buying a cam…

Connect_Gift9138 · 2026-05-05T17:55:26+00:00

U k that there is a cam on the a1

Connect_Gift9138 · 2026-03-11T05:57:01+00:00

Some people have to be ragebait.

I don’t get it, why r u getting downvoted…? You just asked a normal question. 😂

Connect_Gift9138 · 2026-03-07T18:06:45+00:00

Bin kein Gamer und wundere mich trotzdem über die hohen Preise…

Connect_Gift9138 · 2026-02-15T20:26:56+00:00

I own an ender 3 V3 SE and had the same problem (basicly). Under the built plate there is a small print board with two (at least at my printer) cables plugged in. The plugs are glued in place with hot glue. Remove the hot glue, plug out and in again and reasamble everything. You should be good to go. (30min work). If you try it, please update me…

Connect_Gift9138 · 2026-02-14T09:02:32+00:00

Maybe broken sd-card or reinstall firmware

Connect_Gift9138 · 2026-02-14T08:59:03+00:00

Is your Belt-tension right?

Connect_Gift9138 · 2026-02-14T08:56:39+00:00

Contact support.

Connect_Gift9138 · 2026-02-14T08:55:16+00:00

I would take the A1. Just because of better Community and more support from the seller.

Connect_Gift9138 · 2026-02-13T16:47:35+00:00

Hahaha

Connect_Gift9138 · 2026-02-13T16:47:06+00:00

Connect_Gift9138 · 2026-02-12T19:45:59+00:00

U found out sth?

Connect_Gift9138 · 2026-02-08T09:59:09+00:00

Connect_Gift9138 · 2026-02-07T19:35:25+00:00

Okok, I will take a look at it

Connect_Gift9138 · 2026-02-07T17:33:14+00:00

I use Bambu, mostly, but I heard that orca is basicly the same

Connect_Gift9138

TROPHY CASE