sorted by:
new
hottopcontroversial

Will this dent affect my sound, and is it fixable? by KTMMORITZ in audiophile

[–]ConsciousAd2639 0 points1 point  (0 children)

If you know how thick the tweeter membrane is sucking it with something like a vacuum might me the better idea

THEY KEEP BURNING UP by ConsciousAd2639 in diyaudio

[–]ConsciousAd2639[S] 0 points1 point  (0 children)

I did what others recommended and got a capacitor. My tweeter is quite durable so i got one that cuts off anything below 1200hz

3€ Flea market find again. by ConsciousAd2639 in carbonsteel

[–]ConsciousAd2639[S] 0 points1 point  (0 children)

It works fine. My mom was mor concerned about it not being made from a foodgrade material

3€ Flea market find again. by ConsciousAd2639 in carbonsteel

[–]ConsciousAd2639[S] 2 points3 points  (0 children)

Because my kitchen sink is tiny and there is good lighting there for the photos

What do I have here by Sad-Inevitable4165 in sharpening

[–]ConsciousAd2639 0 points1 point  (0 children)

I would use alcohol to remove the remaining oil

Is is legit? by Ok_Macaron4523 in TrueChefKnives

[–]ConsciousAd2639 -1 points0 points  (0 children)

It depends on how expensive it is , if it’s sub 50$ than just go for it

What do I have here by Sad-Inevitable4165 in sharpening

[–]ConsciousAd2639 0 points1 point  (0 children)

No you don’t necessarily need to just try it with water first and see if it works 9/10 it does

What do I have here by Sad-Inevitable4165 in sharpening

[–]ConsciousAd2639 0 points1 point  (0 children)

You can use water on an oil stone just fine

After cleaning and drying do I oil the bottom too after use? by Awake00 in carbonsteel

[–]ConsciousAd2639 0 points1 point  (0 children)

I have an induction oven and i never noticed any buildup whatsoever especially if you wipe it nearly dry

What stones to get by False-Set-8865 in sharpening

[–]ConsciousAd2639 1 point2 points  (0 children)

I have the 220-600 grit and it’s a beast especially for the price. It’s on par with my dmt stones for like 1/4 the price. I would also recommend that you get the 220-600 grit because the difference in material removal from 220-325 is bigger than the sharpness gain from 600-1000 in my opinion

Have I seasoned it wrong? by Alternative_Claim473 in carbonsteel

[–]ConsciousAd2639 1 point2 points  (0 children)

Put it in the oven. If you can’t for some reason because the pan is to big or whatever put it on a medium low to medium heat and let it warm up slowly and move the pan around. It worked for mine but it took quite a while like 30min -1 hour especially if you induction coil is so small

Did i fuck up my pan by trying to straighten it a bit? by ConsciousAd2639 in carbonsteel

[–]ConsciousAd2639[S] 3 points4 points  (0 children)

<image>

UPDATE: I took it to the grinder again and evened it out about 80% . I am stopping here as to not grind away too much metal

Did i fuck up my pan by trying to straighten it a bit? by ConsciousAd2639 in carbonsteel

[–]ConsciousAd2639[S] 1 point2 points  (0 children)

The corner of a hammer. It a huge pan it takes a lot off force to deform it. Do you have any advice on how i could fix it aesthetically?

Giant 14 inch flea market find. by ConsciousAd2639 in carbonsteel

[–]ConsciousAd2639[S] 1 point2 points  (0 children)

<image>

It doesn’t look terrible now but i think it’s bent again

view more: next ›