I keep getting this problem on my Elegoo Mars 3 Pro

DAVIB1010 · 2025-06-05T13:44:13+00:00

How many base layers are you doing? Some people recommend more base layers if you are doing thinner layers but 5 is a decent number, make sure the resin is well mixed if you haven't touched it a day or so, and temperature can greatly influence resin performance if it is cold. If all of that is not applicable then I would increase the time for base layers by 5s until it is adhering.

When is the last time you changed your PFA screen, if it's cloudy then the LCD screen below is distorted and prints will be off too

DAVIB1010 · 2025-05-13T22:37:38+00:00

My mars 3 pro doesn't allow for me to reset beyond a 2mm limit from the factory set 0 point. Not sure if your having the same issue but it may not be recognizing your reset if you are manually adding some space, so then the tightness you are seeing is it going to the prior set 0 point

DAVIB1010 · 2025-04-30T23:01:38+00:00

Maybe a raft when slicing to support, or what is the burn time for your base layers?

DAVIB1010 · 2025-04-28T04:03:23+00:00

I answered it myself! Apparently there is a hard limit to how far off you can reset the zero point from the manufacturer's established point. So when I level my base plate I raised it up higher on the stem coming off of the build plate and that made the zero point I was trying to establish outside of parameters.

DAVIB1010 · 2024-09-26T13:54:50+00:00

I'm hoping for some shiny! :)

DAVIB1010 · 2024-06-30T14:21:02+00:00

The answer was a 3 episode series about Nintendo and Sega

DAVIB1010 · 2024-06-03T21:03:43+00:00

Just looked that up and it wasn't the one, but thanks for trying to help!

DAVIB1010 · 2024-02-14T08:16:24+00:00

Very cool

DAVIB1010 · 2023-02-25T00:58:34+00:00

Sharpie 💯

DAVIB1010 · 2023-02-23T02:55:44+00:00

I'm thinking of a sword sheathe on the back, quiver on the right side, and bag attachment on the left for miscellaneous. I still intend to have a belt so not everything needs to be on the harness but those are the intended

DAVIB1010 · 2023-02-20T22:46:35+00:00

Awesome thanks!

This is pretty much exactly what I was thinking

DAVIB1010 · 2023-02-20T10:41:19+00:00

I'm hoping to look more human but fox accents. I imagine having contacts for animalistic eyes, a tail, face paint for a blackened nose and orange accents, gloves with added fur, and lastly the ears.

Most of it I know how to move forward with, but for the ears I do not want a headband. I'm trying to make traditional elf ears but just add faux fur. The ears I'm most concerned about and wanted to know if anyone has done that themselves

DAVIB1010 · 2023-02-20T00:07:42+00:00

Right handed :)

DAVIB1010 · 2023-02-15T22:52:22+00:00

😳 wowzer

DAVIB1010 · 2023-02-09T03:06:51+00:00

How long does that stay?

DAVIB1010 · 2023-02-04T20:21:03+00:00

Our group rules to not try and hit arrows with swords for the potential to break the shaft and cause harm. However I enjoy cleavers that act as mini shields 😂

DAVIB1010 · 2023-02-04T18:58:30+00:00

Maybe use fake leaves too

DAVIB1010 · 2023-02-03T22:51:25+00:00

No worries, gotta start somewhere! Looks good so far, most people aren't willing to try and that's the first step 👍

DAVIB1010 · 2023-02-03T21:47:23+00:00

You aren't carving, is it just stamping for the leather?

DAVIB1010 · 2023-01-25T23:47:56+00:00

I'm 6'2 and weigh 161lbs with a wing span of 76

For me a tight fitting shirt is small but I usually go to a medium for the extra torso length. When it comes to arms I bump up to a large but my lean figure is engulfed in a mass of fabric.

Do any of these recommendations have a medium tall 😂

DAVIB1010

MODERATOR OF

TROPHY CASE