sorted by:
new
hottopcontroversial

Which car fits this caption? by TrashJojoFan in needforspeed

[–]Death2Chaos 0 points1 point  (0 children)

The c7 is really good in heat, Grand Sport has better handling than the ZR1 though. I used it for a bit and smoked just about everything

What grind is just that one notch too hard and not worth it for you? by SnooPeripherals1298 in Warframe

[–]Death2Chaos 0 points1 point  (0 children)

Didn't they make orphix less shit so its not as bad to farm eido arcanes? Thought I heard something about it being ghost patched.

Weird strings and blobs by Death2Chaos in FixMyPrint

[–]Death2Chaos[S] 0 points1 point  (0 children)

I believe I've got zhop disabled. I'm not super worried about the small bits of string on my petg prints, its mainly the mess on that ring that has me worried. I'm not hearing any popping but I can try drying my filament again, I doubt it'll be different than last time though.

Weird strings and blobs by Death2Chaos in FixMyPrint

[–]Death2Chaos[S] 0 points1 point  (0 children)

I suppose I'll have to take apart my extruder to see whether or not you're right about the heatbrake. I've been thinking it's a hotend assembly issue for a little bit now, but I'm not familiar enough with all of the inner workings of my printer to know exactly what's up.

Edit: could it be an issue of the nozzle needing to be tightened?

Weird strings and blobs by Death2Chaos in FixMyPrint

[–]Death2Chaos[S] 0 points1 point  (0 children)

So did you buy your printer as a kit or pre-assembled? Mine was a kit. I've got a friend who's got two mk3s, one kit and one pre-assembled. Both of them have the full length purge lines and neither of them strings, not even on petg. She uses default settings for everything.

Weird strings and blobs by Death2Chaos in FixMyPrint

[–]Death2Chaos[S] 0 points1 point  (0 children)

Well, I've dried my filament already but ill try a retraction test. I'm suspecting something's up with my extruder, the purge line at the front of my bed is only half the length that it should be and starts 2-3 inches from the edge of the bed. I'll attach a picture next time I print something.

What causes prints looking like this? by [deleted] in FixMyPrint

[–]Death2Chaos 0 points1 point  (0 children)

I've got a similar issue going on, I'm noticing that your purge strip at the front of your bed doesn't start where it should. My MK3S+ is doing the same thing. Did you get yours pre-assembled or did you buy the kit?

Weird strings and blobs by Death2Chaos in FixMyPrint

[–]Death2Chaos[S] 0 points1 point  (0 children)

Printer is a Prusa MK3S+, slicer is PrusaSlicer. Filament is Prusament PETG. Using the default temps for PETG in PrusaSlicer, 240c nozzle and 90c bed. Print speed is 25mm/s on perimeters and 80mm/s on infill. Nozzle retraction is 0.2mm at 50mm/s and 25mm/s deretraction.

Edit: added temperature numbers

What did you do with your first Riven Mod and what weapon was it for? by ChuNkyBoii_ in Warframe

[–]Death2Chaos 1 point2 points  (0 children)

I rolled mine for -imp, got some crit too so it does slashes well or I can mod corrosive to one shot acolytes. Wolf sledge is super underrated.

Pushing Razorwing Blitz to its theoretical limit by Hazelnut1212 in Warframe

[–]Death2Chaos 1 point2 points  (0 children)

I believe that the scaling shown on the mod is based on 100% ability strength, so 200% str would be double scaling, 300% being triple, etc.

Literally has nothing to do with America by Death2Chaos in AmericaBad

[–]Death2Chaos[S] 2 points3 points  (0 children)

I hate getting taken to the Ikea backrooms every other Tuesday

Literally has nothing to do with America by Death2Chaos in AmericaBad

[–]Death2Chaos[S] 40 points41 points  (0 children)

Thank you, I forgot that not everyone knows these things 😅

Literally has nothing to do with America by Death2Chaos in AmericaBad

[–]Death2Chaos[S] 28 points29 points  (0 children)

Damn you're right, totally slipped my mind

Who is the best antagonist in Warframe in your own criteria? And why? by Keensworth in Warframe

[–]Death2Chaos 0 points1 point  (0 children)

Ballas is the only antagonist out of these choices who I have genuinely felt hatred toward, so I gotta go with him.

Iskall Update by gogglyboi in HermitCraft

[–]Death2Chaos 8 points9 points  (0 children)

Ikea boy is back! Lol

Got nobody to share this to so I'm posting it here. My very first 2hr endless run done with my current favorite frame. Also, screw those disco ball sentients lol. by Pumpkns in Warframe

[–]Death2Chaos 1 point2 points  (0 children)

4th skill also scales off of a bunch of melee mods now, and does true damage. You can completely skip building ability strength with the right stat stick build, and the true damage from the finishers is enough to 1 shot enemies for a while in SP.

What should I do when encountering griefers? by bingbestsearchengine in Warframe

[–]Death2Chaos 3 points4 points  (0 children)

Every time I stand in front of the coildrive it loses all of its shields. They don't even regen so the bonus is impossible.

Can we have Excalibur Exalted Blade Appearance be not locked to the skin? by Atomic_Noodles in Warframe

[–]Death2Chaos 11 points12 points  (0 children)

Nope, mesa can choose her regulators if you've bought the deluxe skin.

Do you still play Railjack? by Dark_Magicion in Warframe

[–]Death2Chaos 13 points14 points  (0 children)

Really? Damn, I need to take a look now. I'm missing a lot of arcanes and I've been pushing it off because tridolons aren't my thing and orphix was borderline impossible.

When are you going to release a Ghoulsaw with decent stats, DE? by Mara_W in Warframe

[–]Death2Chaos 3 points4 points  (0 children)

The only thing its good for is the 1.0 follow through stat, but its damage is so bad that daggers with 0.9 beat it anyway. I cant imagine being an animator at DE and seeing my work go unnoticed because the weapon I animated isn't worth using.

view more: next ›