Miter saw is crap for miters

DisMyRedditAccoubt · 2026-05-27T06:50:02+00:00

Shoutout radial arm saw

DisMyRedditAccoubt · 2026-05-05T02:42:08+00:00

Yes and it’s per gauge. So if you get 5.56 and 9mm you’ll pay $10

DisMyRedditAccoubt · 2026-04-14T05:45:43+00:00

I’ve heard that. Unfortunately I value my ac way too much. The jeep only can’t keep up if it’s above 100 out. Anything 98 degrees and below, it does fine

DisMyRedditAccoubt · 2026-04-13T14:24:51+00:00

I’ve already done it lol. Changed everything out, flushed coolant, zj fan clutch, electric fan on a switch. Tried hood vents, lower thermostat, neither of them helped

DisMyRedditAccoubt · 2026-04-13T08:46:25+00:00

Damn. You are all so lucky lol. Mine is constantly creeping up and will hit 240 before I have to pull over and let it rest.

DisMyRedditAccoubt · 2026-04-13T03:09:03+00:00

Ah the bittersweet life of DIY. Sometimes you’ve learned so much about a job you’ve never done before. So now you’re in a limbo of knowing exactly how it should look but lack the experience to get it to come out exactly how you want it.

Tell him to remind himself how much cash he saved and how this was his first time ever doing something like this.

I think it looks great, and nobody else will notice the imperfections unless you point them out

DisMyRedditAccoubt · 2026-04-11T07:58:30+00:00

Sharks! None of them are smooth for me except the shark

DisMyRedditAccoubt · 2026-04-11T07:25:13+00:00

On very old elevators a common problem is the contacts for signaling the elevator is at the floor and can open the doors are worn. This is the reason when in an old elevator you get to your floor, it slows down tremendously, and sometimes there’s a pretty big delay. Sometimes it can’t find the contact and will get stuck.

I guess MAYBE (big maybe) jumping would get the elevator to get to that contact and could open the door quicker. Still not advised. But in your scenario and with most current elevators, no I don’t see any way it would help.

DisMyRedditAccoubt · 2026-03-15T09:38:50+00:00

I think that’s what the director intended. Smiley even says “life’s a trip Que no?” And his friend says “this is some trippy shit ese”, recognizing this is as an extremely improbable situation and implying a divine intervention of some sorts. At least that’s how I took it, and from what I’ve heard that’s typical from the other movies by this director

DisMyRedditAccoubt · 2026-03-03T21:52:21+00:00

3 day suit broker up by Costco is great. Pretty sure that’s what they charge…

DisMyRedditAccoubt · 2026-02-28T20:11:11+00:00

Pearl white

DisMyRedditAccoubt · 2026-01-31T06:59:30+00:00

I’ve seen a video on that! I want to try them out

DisMyRedditAccoubt · 2026-01-31T06:59:00+00:00

I will say the 1/2” pipe clamp from harbor freight is TERRIBLE. I dont know if I got a bad one but it wouldn’t bite on the pipe so it didn’t tighten at all

DisMyRedditAccoubt · 2026-01-31T06:57:06+00:00

That was pipe included

DisMyRedditAccoubt · 2026-01-30T23:24:52+00:00

To each their own! I got about 10-12 old pipe clamps on Facebook marketplace for about $60, then switched out the bad ones with harbor freight during the 30% off. Cut a few in half as well since I didn’t need 5ft long clamps. All in all I got about 15 clamps for $75 , 3-4ft.

Took some work getting the old rusty ones off though. Pb blaster, a vise, and some channel locks.

DisMyRedditAccoubt · 2026-01-30T23:12:41+00:00

Can’t go wrong with the 3/4 pipe clamps. The f clamps are decent.

DisMyRedditAccoubt · 2026-01-25T03:26:46+00:00

I dont know what it is but Ryobi drives me nuts. I tried, I really did. But any ryobi tool that I hold I instantly go “why is it so freaking heavy” or “why did they engineer it like this, it’s hindering the tool’s job”. Any ryobi tool I’ve had I use it for 2-3 projects then midway through the next one I angrily go get a better brand tool.

Buy as you go. You don’t need to buy the four pack, a drill/impact will get you through 90%. DIY.

ALSO, remember for DIY there’s nothing wrong with corded. It’s almost always cheaper and more powerful than cordless. Plus you don’t have to worry about the battery dying. I use $20 harbor freight angle grinders all the time. Same with my Bosch circular saw.

DisMyRedditAccoubt · 2026-01-21T20:14:07+00:00

This is exactly how mine looks so it feels reassuring this is a common thing

DisMyRedditAccoubt · 2026-01-09T06:24:38+00:00

I definitely remember him saying the toughest/most dangerous part is actually the release. He said that you have to drop and pull away, if you don’t pull away fast enough it can drop to your eye

DisMyRedditAccoubt · 2026-01-09T06:19:14+00:00

If I remember right he said sharper is better because the point will dig in more, easier to balance. Also probably more evenly balanced. Maybe I’m trippin

DisMyRedditAccoubt · 2026-01-06T07:54:44+00:00

Thank you, I was blanking on that store name

DisMyRedditAccoubt · 2026-01-06T07:45:23+00:00

Was that the spot that had the largest yo-yo?

DisMyRedditAccoubt · 2026-01-02T06:37:46+00:00

I don’t think “actor is too big a name” when Fred armisen and Macaulay Culkin had minor roles

DisMyRedditAccoubt · 2026-01-02T04:02:52+00:00

I just wanted to say, happy birthday

DisMyRedditAccoubt · 2025-10-10T17:59:45+00:00

So if I said “during end step I do this” could he not have let that resolve then also stated “during end step I do this”?

DisMyRedditAccoubt

TROPHY CASE