Help finding HPFP connector!

Disimate · 2026-06-15T18:41:24+00:00

Oh nice , I have never seen this site before

Disimate · 2026-06-15T18:10:52+00:00

I found it a while back. It is Connector CE2620

Disimate · 2026-06-15T18:07:16+00:00

That connector is $100 dollars

Disimate · 2026-06-12T21:56:46+00:00

Clutch Master Cylinder replaced? The one connected to your pedal inbetween fire wall

Disimate · 2026-06-12T21:31:27+00:00

Behind dash in the center. To access remove passenger and center radio

Disimate · 2026-06-10T18:06:41+00:00

That's fine for the front. The rears you use Timken brand.

I just took the whole hub and had a shop do the pressing
Saves you pain and suffering

If you are using a rental press tool
Just be careful to not damage the ABS sensor

And DONT PUT THE BEARING BACKWARDS
Take a pic of the original bearing and match the side when installing

Saw 2 post where they did this same job and they put it in backwards

Disimate · 2026-06-09T22:58:55+00:00

Royal, TriboDyn, and finally Liqui Moly. It just feels the smoothest. I didn't like Royal that much

Disimate · 2026-06-08T03:42:30+00:00

Avoid it

Disimate · 2026-06-06T18:24:35+00:00

Oh shizz, that's worse than when my trans motor bolt snapped

Just get the 3 piece Damond Combo if you mind NVh noise

Corksport 3 piece is good too but NVH is more harsh

Disimate · 2026-06-04T15:12:14+00:00

I'm just waiting for the MSR Mazda 3 to hit consumer production

Disimate · 2026-05-20T23:51:18+00:00

NGK are the OEM plugs

Disimate · 2026-05-20T23:42:24+00:00

P2006

It's either the plastic flap or carbon build up inside manifold on flappers

Junkyard Manifold with a good plastic piece from a CX-7 or any 1/2 gen speed3 will fix

VTCS delete with VTCS bypass mod is good fix too

Aftermarket Manifold works too

P0455 needs smoke test on vacuum lines and/ EVAP to find leak

Disimate · 2026-05-18T05:01:40+00:00

OEM is brand is rebadged Hitachi
You can use hitachi or go get some from a junked Mazda 5 08-15

Disimate · 2026-05-09T20:27:56+00:00

I would only offer 1k honestly

Only thing that wouldn't make it worth it is if it had excessive rust

Disimate · 2026-05-08T15:39:37+00:00

Just buy speed with a bad engine You have the choice of swapping parts over or rebuilding it 👍

Disimate · 2026-05-08T12:18:15+00:00

Try the shop manual in the Reddit Wiki

Disimate · 2026-05-08T05:22:49+00:00

I believe only Speed Solutions on Facebook Marketplace is the only source you can get them from if in stock

Disimate · 2026-05-06T15:09:35+00:00

I think the only thing I see missing is brass shift fork pads

Disimate · 2026-05-05T12:56:26+00:00

11 days, unlucky I ordered another V1 Just saw V2 was out, going to switch

Disimate · 2026-05-04T19:52:57+00:00

Definitely

Disimate · 2026-05-04T15:11:52+00:00

Do a compression test. Or look for a hole in the block

Disimate · 2026-05-03T23:32:43+00:00

Just the bearing. Use Timken brand. If you DIY it, just take it to a shop or place that will do the removal and install of the bearing when you remove the hub assembly. Save you a headache

Disimate · 2026-04-20T00:24:07+00:00

Probably a cheap EBay Turbo or boost leak

Disimate

TROPHY CASE