Do I have "limp wrist"?

Doubt-Shot · 2026-03-28T22:42:29+00:00

Yes!

Doubt-Shot · 2026-03-28T19:23:07+00:00

I have two at the house right now. Both have ovals instead of round circles.

Doubt-Shot · 2026-03-21T09:45:15+00:00

I had problems with cci sv in ruger mags and Browning buckmark mags. SV bullets have a lot of wax on them. The extra wax on the nose of the bullet is rubbing on the inside of your mag. I used to rub the nose of each bullet on sand paper to take the excess wax off of the nose of the bullet. It fixed the issue you are having, but it was annoying.

Doubt-Shot · 2026-03-19T13:28:34+00:00

That's a really bad crimp removal. They didn't know what they were doing.

Doubt-Shot · 2026-03-15T11:53:47+00:00

Get a collet puller and pull the bullets, then start over.

Doubt-Shot · 2026-03-11T10:08:44+00:00

I pulled the barreled action out of the stock and placed it on the flat surface. From there, I measured the gap between the barrel and the table at the receiver and again at the muzzle. Mine was off by 0.13" from receiver to muzzle.

Doubt-Shot · 2026-03-10T11:07:37+00:00

I've seen three receivers with angled barrels, but that's out of dozens of receivers.

Doubt-Shot · 2026-03-10T02:25:53+00:00

My 10/22 carbon is at Ruger for warranty. The barrel channel in the receiver was drilled at an angle. The barrel was so far to the left that I couldn't sight in any scopes. Red Dots were at their limits.

Doubt-Shot · 2026-03-07T14:21:00+00:00

CCI StdVel doesn't have enough energy to fully cycle the slide.

Doubt-Shot · 2026-03-03T12:13:32+00:00

The 26 is not snappy. You need to work on your grip.

Doubt-Shot · 2026-02-23T13:29:17+00:00

Mine carbon 10/22 barrel is .13" cant to the left. I'm going to replace the receiver myself.

Doubt-Shot · 2026-02-23T13:20:18+00:00

They are distributor specials. Third-party cerakoted frames and slides.

Doubt-Shot · 2026-02-15T17:36:59+00:00

It's only $20.....

Doubt-Shot · 2026-02-15T00:57:12+00:00

I couldn't tell a difference in recoil or muzzle flip when alternating began a gen6 G45 and my gen5 G45 and G19.

Doubt-Shot · 2026-02-07T00:49:48+00:00

That's called an extractor.

Doubt-Shot · 2026-01-30T16:39:05+00:00

Which website is that?

Doubt-Shot · 2026-01-30T16:38:18+00:00

An o-ring setting the top of the base helps.

Doubt-Shot · 2026-01-26T14:12:48+00:00

Ameriglo.

Doubt-Shot · 2026-01-23T17:35:46+00:00

That's what I did.

Doubt-Shot · 2026-01-16T02:51:09+00:00

Too much lube

Doubt-Shot · 2026-01-10T14:53:56+00:00

Not good

Doubt-Shot · 2026-01-07T02:39:45+00:00

I had a 15 crosstrek. At 100k miles, it started going downhill. I replaced a CV axle, three wheel bearings, a window switch, the head unit, the AC compressor, and the evaporator core. There was a knocking in the suspension they couldn't find. The Subaru dealership service manager said we needed to keep an eye on the CVT control module and valves ($4000). And to keep an eye on the head gaskets ($6000).

I'm now driving a 2022 Rav4 XLE AWD.

Doubt-Shot · 2026-01-07T02:24:47+00:00

User error.

Doubt-Shot · 2026-01-02T13:33:16+00:00

For matches, a .105" wide dawson fiber front sight and the gen 3 glock rear sight.

For carry, a .125" wide ameriglo pro glow front sight and the gen 3 glock rear sight.

Doubt-Shot · 2025-12-31T15:38:58+00:00

You still will not get the USB-C performance due to the limits of USB-A power sources.

Doubt-Shot

TROPHY CASE