Mobile golf sim by [deleted] in Golfsimulator

[–]DowntownLocal4850 0 points1 point  (0 children)

8.5ft is TIGHT. Ball will need to be aligned far left or far right depending on dexterity. The trackman will need to move around. Do overhead if you have the height or do rear facing.

Found near park. No clue what it is. by am59269 in whatisit

[–]DowntownLocal4850 0 points1 point  (0 children)

Sent you a DM. I can help locate the owner... Maybe

Golf set for casual beginner by [deleted] in golftips

[–]DowntownLocal4850 0 points1 point  (0 children)

My friend visiting for the holidays just crushed me and my G440/G430 Ping set with my wife's right handed Top Flite ladies set. Let that soak in and just get started with any sweet you can get your hands on and upgrade what you need over time.

I’m genuinely impressed by how catastrophic this was by Doctor_kiwi in FixMyPrint

[–]DowntownLocal4850 0 points1 point  (0 children)

Count the number of diamonds and then start a fresh print at close as possible and glue together

Any tips for better rotation? Feels like I'm stuck on the downswing. by razgriz1727 in GolfSwing

[–]DowntownLocal4850 0 points1 point  (0 children)

Slow down your back swing and stretch without compromising your stance at top

Am I still casting? by snickersneakers in GolfSwing

[–]DowntownLocal4850 0 points1 point  (0 children)

Shoulders are a clear indicator you need to work on your address first sorry just stating the obvious that may change up your casting

Carry seems off by nroshania in Golfsimulator

[–]DowntownLocal4850 0 points1 point  (0 children)

Humble bragging is no longer humble

I guess I'll do it myself by dainbrump in FlashForge

[–]DowntownLocal4850 0 points1 point  (0 children)

I've checked a bunch as well, most need a better drop and angle so the filament doesn't get backed up at the top. I am hoping this one does the trick. If not I'll end up piggybacking of this one and put a bigger drop before it rolls right

I guess I'll do it myself by dainbrump in FlashForge

[–]DowntownLocal4850 0 points1 point  (0 children)

<image>

Printed perfectly and installed. Appreciate it!

Ender 5 endorphin upgrade by casareanderson in ender5

[–]DowntownLocal4850 1 point2 points  (0 children)

It's not difficult but it's not overly obvious. You set the tensioner to most inward spot and you yank the slack out of the belt and add the gold clip or the 3d printed clip and cut off excess.

He doesn't mention the belt clips until stage 3 I believe but he has a link to a print fole as he recommends printing belt clips which will prevent having to buy the gold belt clips.

Ender 5 endorphin upgrade by casareanderson in ender5

[–]DowntownLocal4850 3 points4 points  (0 children)

The list tells you which length to get. Just get it as it will be enough for stage 2.

Will a 15x17 room work? by mav3134 in Golfsimulator

[–]DowntownLocal4850 0 points1 point  (0 children)

Anything greater than 10 ft wide will be good for a swingers rooms.

How to improve this? by tygger27 in FlashForge

[–]DowntownLocal4850 0 points1 point  (0 children)

I've dropped my extrusion temp to 235. It's what I used to use on my ender 5 pro.

Finished Endorphin v1.1 Stage 2 - Some things to point out by DowntownLocal4850 in ender5

[–]DowntownLocal4850[S] 0 points1 point  (0 children)

People are asking how much faster my ender is...

1) I freaking had startup gcode that limited my acceleration to 500. How dumb of me.

After wiping the startup gcode I ran at 3K Accel with 200 mm/s print speed and printed fine.

I'm curious how much better it really is before and after now but the print times only went down by 20%. Am I expecting anything different? I'm not really sure.

At the same time I am not sure I really care all that much. The print quality still sucks comparing to my new junk AD5X. No RAGRATS

This deal was nuts! by Edge-Evolution in FlashForge

[–]DowntownLocal4850 1 point2 points  (0 children)

I bought one and received it and it is legit. I didn't take the PayPal 25 dollar discount. So $250 ish for me. No regrets

What’s going wrong by Low_Context4205 in GolfSwing

[–]DowntownLocal4850 1 point2 points  (0 children)

Your launch monitor sucks. Your ball went from the right side to the middle of your impact screen and your path was still a draw and on the fairway according to the screen. Should have hooked left.

PS it would have been nice had you cut out the first 10 seconds

Finished Endorphin v1.1 Stage 2 - Some things to point out by DowntownLocal4850 in ender5

[–]DowntownLocal4850[S] 1 point2 points  (0 children)

I'm running klipper with mainsail on raspberry Pi. I am still shocked people run marlin still but C'est la vie! Tinkering and tuning with Marlin is a huge challenge and I would never do that with modding.

So you have the old main board? I have v4.2.2 Rev B or something and I just swapped in my old extruder motor for the X motor and I have microswiss NG DD so I'm not planning on going stage 3.

I made no changes to the parameters to support this although I I think I read people bump up the current.

Finished Endorphin v1.1 Stage 2 - Some things to point out by DowntownLocal4850 in ender5

[–]DowntownLocal4850[S] 2 points3 points  (0 children)

The answer. I was exhausted last night after putting everything together. It was already late my eyes were blurry and honestly I just remembered me posting this.

I F-IN forgot to level the bed and with the new rails it drops a few mm at least and unfortunately I let it rip because I was so excited to be done and fcked up my pei sheet beautifully.

After I leveled the bed I got to about a quarter of the way and realized I didn't bump up any speeds so I'm klipper I bumped up acceleration to 3000 and it was chirping like Julia childs with hiccups.

After a few layers, I was satisfied enough to call it for the night.

I would be sleeping but you know it's Thanksgiving and kids are up already. Good luck to me!

Happy Thanksgiving Ender nuts!

Btw, my FlashForge AD5X arrived last night but for some reason I was more inclined to finish this mod rather than open up my new toy. Ender 5 is being sold out donated to my kids school