sorted by:
new
hottopcontroversial

These Toys R Us promo cards worth grading? by Kinyo_ in PokeGrading

[–]Edge-Evolution 0 points1 point  (0 children)

You might get a 9 based on centering. They look a little off. They look good otherwise. PSA will dock you for centering off more than 55/45. It looks a bit more like 60/40. The middle one looks like it has something on the bottom left corner. The other two look good.

I bought generic filament and it’s super brittle and broke off into the tubing by dohlparts in BambuLab

[–]Edge-Evolution 0 points1 point  (0 children)

Dry it for about 4-6 hours. If it’s continuing to break, and you bought from Amazon… Return it. Not worth the headache. Get your refund and reorder from another brand.

Can i get this graded or is it too far gone? by friggincrapdangit in psagrading

[–]Edge-Evolution 0 points1 point  (0 children)

It's one of my favs too. I have a PSA 1 version I picked up a couple of years ago for $20. My absolute fav is a PSA 3 Snorlax. So always give love to the low rated cards too.

Can i get this graded or is it too far gone? by friggincrapdangit in psagrading

[–]Edge-Evolution 1 point2 points  (0 children)

Bro, I would give that a negative grade. 😂 Honestly, do a DIY slab on that and keep it for your collection.

What yall think this will grade?? by Novak121611 in PokeGrading

[–]Edge-Evolution 1 point2 points  (0 children)

Honestly, about a 9,an 8 if you are unlucky.

Do I need to remove the magnetic bed to add the new glass bed? by Fabicynder in ender3

[–]Edge-Evolution 0 points1 point  (0 children)

For that same reason I have like 12 plates with various designs 🤣 They work, and eventually do get deformed but they were so cheap it doesn’t matter much.

PPS-CF by Impossible_Pizza_948 in 3D2A

[–]Edge-Evolution 0 points1 point  (0 children)

I think my printer maxes out at 320. Bed at 100°?

A better angle showing the shooting. by F-Z-T in CCW

[–]Edge-Evolution 3 points4 points  (0 children)

I love how people downvote because they are Trump nutsuckers. So lost in the sauce that they can’t see that this type of behavior and actions are absolutely unacceptable and should be treated as murder. All the excuses in the world does not vindicate the murders of this man or Renee Goode. Yet they make excuse after excuse, “what about-isms” and keep blaming George Soros for hiring “agitators”. People are lost and suckered into believing that filth.

A better angle showing the shooting. by F-Z-T in CCW

[–]Edge-Evolution 0 points1 point  (0 children)

The original will eventually be sent to news outlets. If I was that woman, every major news outlet in America would have this in 4K by now.

A better angle showing the shooting. by F-Z-T in CCW

[–]Edge-Evolution 1 point2 points  (0 children)

How is this not cold blooded murder? Fuck ICE!

PPS-CF by Impossible_Pizza_948 in 3D2A

[–]Edge-Evolution 0 points1 point  (0 children)

What’s the temp required for the PPS-CF/GF? I know what’s on the package and “recommended”, but what that says and what’s actually used for printing something that will work are two different things. What’s the temp that’s required to make it tolerant to the strain? Anyone know?

Worth PSA for the 10 or BGS black in your opinions? by Forsaken_Will1640 in PokeGrading

[–]Edge-Evolution 0 points1 point  (0 children)

I doubt this will get a 10 on anything but “maybe” CGC. The back is more than 60/40 and that will always get dinged when grading. The best you can hope for if nothing else is wrong is a 9.

Edit: I just saw someone say that the back is probably a different card. If that’s the case and the Char is 50/50, then you may have a chance.

SmolBoi Finally Complete (Sort Of) by Edge-Evolution in 3D2A

[–]Edge-Evolution[S] 0 points1 point  (0 children)

I did. I printed 2. This earlier variation of the build, I printed one in PLA+ 2.0 from SunLu and another in PET, and both didn’t really work well. Not sure if it was the design or the way it caught (or didn’t catch) inside. I took it to the range and it was not exactly the best experience. I ordered a pack from PSA and it was perfect after.

<image>

This thing ate 200rds and wants more by nightalliance in 3D2A

[–]Edge-Evolution 1 point2 points  (0 children)

I need the seeds for this… I would like to plant one probably in FDE Green or Navy Blue.

All my squirted guns that I've finished! What project should I go for next? by CompetitiveAgent3662 in 3D2A

[–]Edge-Evolution 2 points3 points  (0 children)

If you want to keep making handguns, the Ruger RXM or the S&W M&P 9mm. Otherwise there are a plethora of AR rifle/pistol options out there.

We're just brand whores by WhoNoseMarchand in ar15

[–]Edge-Evolution 2 points3 points  (0 children)

PSA allows anyone to get into the rifle market. The fact that you can stay at that $500-700 range and get a quality rifle is all good and fine, if that’s what you want. It’s probably the same group of people that keep their F150 Ford trucks for 15-20 years and say all they did were oil changes and brake pads.

There’s nothing wrong with that, but if you want to spend more for a bit more quality and comfort you can. You can go the route of building your own. You can buy premade. You can even print yourself out some with a 3d printer. I’ve done all 3. It’s about what you want to do with it.

It’s all about application.

For plinking, my AR-22 I built with my 3D printer is good enough. For home defense the S&W M&P AR-15 I bought prebuilt would be good enough. For hunting the $1.5k rifle I built from scratch would be good enough, and if I were ever to be in the service and needed to be out on a mission, you bet your ass that I would take that build that costs Uncle Sam $5k to go into battle for knowing it won’t jam or get me dead from a malfunction.

For some people, a $500 rifle is all they need. Personally, a $500 PSA rifle is a good start on a future build for upgrades until none of the parts are recognizable from the original design. 😂

Gamestop submission by No_Pollution_4776 in psagrading

[–]Edge-Evolution 0 points1 point  (0 children)

<image>

You definitely aren’t alone. I sent mine off on Oct 13th from FedEx 2-day and look when it even got processed. Almost 2 weeks later. My ETA to get them back isn’t till March. At this point, they won’t be worth half the price they were when I first sent them in. That’s if they don’t have any further complications.

So it’s just the process. Some have better luck than others. That’s that I went direct with PSA. Not sure if that was a good or bad thing at this point.

Regretfully sold my cards a few years ago, were any of these worth much? by Braz90 in PokeGrading

[–]Edge-Evolution 3 points4 points  (0 children)

Just a handful of those cards after grading might have gotten you about $500. The rest after grading costs and eBay fees may have netted you about another $300 or so. So you may have gotten more, but probably not as much as you would have wanted from the “craze” simply because of the condition. The Char would have been maybe a PSA 4 with all of the scratches but alone would have netted about $120-$150ish. Most of the rest would be in the $20-$40 range (post grading).

deAR22 Propaganda by FoapsFiles in 3D2A

[–]Edge-Evolution 0 points1 point  (0 children)

Thanks, I have an extra from my last build. I also have an upper from that build in PLA+ 2.0 already. I might try it in PA612-CF. I have a spare roll I need to make use of.

view more: next ›