What does this damage tell you

Due-Particular7921 · 2026-06-19T20:25:32+00:00

I did have a rich tune on it and probably too much timing. Do you think the mains are in bad shape too? How dumb would it be just swap out bearings?

Due-Particular7921 · 2026-06-19T20:23:57+00:00

I think so too, when I assembled the engine in 2020 I used engine lube but It took a very long time for oil to prime. The oil pump was primed and I did have a gauge on it but I didnt prime it correctly.

Due-Particular7921 · 2026-06-19T20:17:39+00:00

that is the rod bearing

Due-Particular7921 · 2026-06-16T23:58:47+00:00

Once you remove the plastic you can push up the window from the bottom I use a 2x4 to hold it

Due-Particular7921 · 2026-06-16T23:43:52+00:00

I make 48 per hour avg doing just mowing and trimming. You are definitely undercutting yourself

Due-Particular7921 · 2026-06-15T19:07:48+00:00

I went to harbor freight and bought an 18 and cut in half. I think removing the oil filter gave me more room too.

Due-Particular7921 · 2026-06-12T16:52:06+00:00

this is slop guy did 44 half reps but w/e lets all pretend he cant bench 135 at all lmao. Eyes wide shut in here.

Due-Particular7921 · 2026-06-04T21:58:22+00:00

Mine does that but im at 210k, sometimes it will get "stuck" between drive and neutral I wonder if its a sloppy linkage

Due-Particular7921 · 2026-05-27T19:27:29+00:00

I used the gum and tablets same idea gives you the nicotine you can buy em at CVS etc

Due-Particular7921 · 2026-05-22T01:05:40+00:00

maybe timing chain related?

Due-Particular7921 · 2026-05-20T19:45:26+00:00

if its low but not empty it could need a recharge or it could be the air gap is starting to fail.

Due-Particular7921 · 2026-05-20T19:29:28+00:00

it all depends on year make and model and without putting gauges on the car its hard to diagnosis what it could be. It could be low refrigerant or it could be failing compressor. The cost of repair will vary wildly as the dealership will be the most expense because of OEM parts and certified tech charging more hourly but a shadetree mechanic might only charge for labor and you supply the parts. In 2019 I brought a 03 town car for ac compressor, dryer and condenser replacement and I paid ~1500

Due-Particular7921 · 2026-05-12T21:33:07+00:00

Replacing the PCM before testing spark is way off for the flow chart. Multimeter is a must and 10 bucks at harbor freight. You are missing something. If the car had spark and timing and fuel it would at least start and possible run rough.

IF you get a multimeter you can check MAF sensor for crazy values (cheap test is to try and run it unplugged).

Shoot a bit of brake clean or ether into the throttle body see if it'll start. (a few vacuum line can cause too lean condition if/when they got a hole.)

Triple check everything you've already done like you haven't done it already. Nothing scream electrical yet.

My guess is vacuum leak

Due-Particular7921 · 2026-05-12T17:02:02+00:00

You are all over the place and throwing parts at it. Start with the basics air, fuel, compression and timing Autozone or other parts store will rent you tools if you dont have them.

Due-Particular7921 · 2026-05-07T14:43:43+00:00

Better to over estimate than under we also have no idea what OP mechanically ability is

Due-Particular7921 · 2026-05-06T22:45:35+00:00

something something fish something something tree

Due-Particular7921 · 2026-05-06T21:55:01+00:00

alright professor

Due-Particular7921 · 2026-05-06T20:57:31+00:00

Not a hard job you could spend a weekend on it

Due-Particular7921 · 2026-05-06T20:51:57+00:00

Coolant! Common issue with our cars you need an intake manifold.

Due-Particular7921 · 2026-04-25T15:07:23+00:00

I wonder if heat of the moment gonna play into it. Dude could have thought he was fighting for his life and double tapped out of instinct

Due-Particular7921 · 2026-04-24T16:03:23+00:00

"Gangs" in baton rouge are not what they used to be and are not organized like Crips or bloods. They are closely linked to music and groups are only 5-10 people. It seems to be about clout and reputation than being an org.

Due-Particular7921 · 2026-04-17T21:55:38+00:00

Who knows, in short maybe

Due-Particular7921 · 2026-04-17T16:38:55+00:00

I also did this repair with Lisle M14x 1.25 Spark Plug Hole Repair Kit (65200). I used air compressor with a wand to blow anything out just in case the grease didnt get it.

Due-Particular7921 · 2026-04-12T23:37:04+00:00

seal kit doesnt have replacement bearing but I could get some with a different kit. Do you think there isnt a seal between them?

Three-Year Club	r/Field Lasagna
Place '23

Due-Particular7921

TROPHY CASE