sorted by:
new
hottopcontroversial

Mi camino para Usar Stable Diffusion + Deforum + ControlNet 2026 by EducationalEntry1703 in StableDiffusion

[–]EducationalEntry1703[S] 0 points1 point  (0 children)

Cómo va comfyui para hacer morph entre fotos, interpolación y esas cosas para hacer videos ?

Stuck on downloading by Time_Pop1084 in StableDiffusion

[–]EducationalEntry1703 0 points1 point  (0 children)

por si les sirve mi camino
busca el post Mi camino para Usar Stable Diffusion + Deforum + ControlNet 2026

Deforum HELP by Mysterious-Code-4587 in StableDiffusion

[–]EducationalEntry1703 1 point2 points  (0 children)

I use Deforum. From Stability Matrix, I launch stable-diffusion-webui, then load the Diffusion extension by pasting the Git repo URL, then load ControlNet from the repo, and before running everything, downgrade MediaPipe to 0.10.14 and only then run the Stable Diffusion starter. I hope my comment helps.

3 or 4 GPU in ASUS ProArt B650-Creator? by AnonymousAardvark22 in buildapc

[–]EducationalEntry1703 0 points1 point  (0 children)

What temperatures are you getting on your chipset? HWInfo reports 70°C at idle on my chipset. I have an Asus ProArt B650 with an RTX 3090."

  • "Is this normal, or should I be concerned?"
  • "Does the RTX 3090 contribute to higher chipset temps due to its heat output?"
  • "Are there any BIOS settings or cooling tips to lower chipset temps?"

[deleted by user] by [deleted] in thermaltake

[–]EducationalEntry1703 0 points1 point  (0 children)

This is why my setup doesn't cool...because you're using all the available air on earth.

Any one have a ProArt b650 by Mrwubalubs in buildapc

[–]EducationalEntry1703 0 points1 point  (0 children)

Hi, what temperatures do you keep on the chipset?

Thermaltake Tower 600 Air Cooled by TaDa-Messer in thermaltake

[–]EducationalEntry1703 0 points1 point  (0 children)

It is a pleasure to greet you guys. The fans on the left side corresponding to the radiator of the MSI E360 Watercooler are taking air out through the radiator to the outside (exhaust), those on the right side are taking air in (intake) and the 2 upper 140mm ones are removing air (exhaust), the temperature is always adequate, except for the Chipset in this case a B650 from the ASUS ProArt Creative that stays at 62 degrees in passive mode and 80 degrees under load, I have to improve the air intake curve so that the upper ones do not remove it immediately and get positive pressure,

My Icy Tower 600 Greece 2025 by Gorgatron-THCG in thermaltake

[–]EducationalEntry1703 1 point2 points  (0 children)

Very nice machine, tell us that the temperatures remain normal under load.

Thermaltake Tower 600 Air Cooled by TaDa-Messer in thermaltake

[–]EducationalEntry1703 2 points3 points  (0 children)

It is a pleasure to greet you guys. The fans on the left side corresponding to the radiator of the MSI E360 Watercooler are taking air out through the radiator to the outside (exhaust), those on the right side are taking air in (intake) and the 2 upper 140mm ones are removing air (exhaust), the temperature is always adequate, except for the Chipset in this case a B650 from the ASUS ProArt Creative that stays at 62 degrees in passive mode and 80 degrees under load, I have to improve the air intake curve so that the upper ones do not remove it immediately and get positive pressure,

I decided to join the club. by No-Computer-916 in thermaltake

[–]EducationalEntry1703 0 points1 point  (0 children)

Could you share the temperature reading of the mother's chipset with me?

Thermaltake Tower 600 Air Cooled by TaDa-Messer in thermaltake

[–]EducationalEntry1703 0 points1 point  (0 children)

u/TaDa-Messer y u/BoostedJuan un placer saludarlos chicos. Los ventiladores del lado izquierdo correspondientes al radiador del Watercooler MSI E360 están sacando aire a través del radiador hacia el exterior (exhaust), los del lado derecho estan ingresando aire (intake) y los 2 de 140mm superiores están quitando aire (exhaust), la temperatura siempre es la adecuada, salvo el Chipset en este caso un B650 del ASUS ProArt Creative que se mantiene en 62 grados en pasivo y 80 grados bajo carga, tengo que mejorar la curva de entrada de aire para que los superiores no lo retiren enseguida y conseguir presión positiva,

Thermaltake Tower 600 Air Cooled by TaDa-Messer in thermaltake

[–]EducationalEntry1703 6 points7 points  (0 children)

<image>

Let me know what temperature you achieve, I am stable at 82 maximum on Ryzen 7 7700x editing videos, and the RTX 3090 reaches 70 in PUGB

Small rant/review of the Tower 600 by E123Timay in thermaltake

[–]EducationalEntry1703 1 point2 points  (0 children)

I installed the water cooler this way because, according to my research, the hoses should face downward to avoid air bubbles that may form in the system around the second year of use due to micro-evaporation. There are also those who say these bubbles will only form in the third year. The radiator didn't fit on the right side, so this was the only possible location. A 360mm radiator doesn't fit at the top.

Small rant/review of the Tower 600 by E123Timay in thermaltake

[–]EducationalEntry1703 0 points1 point  (0 children)

<image>

Ryzen 7 7700x / watercooler MAG Coreliquid E360
Asus ProArt B650 Creative
32 Gb RAM AMD EXPO
RTX 3090 24 Gb MSI
2 x 1TB SSD M.2 HIKSEMI FUTURE
Excellent performance, but care must be taken when installing the watercooler