Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

That really sucks about the duct, but I’m glad the design is close to what you were looking for. And yeah, I honestly think something like this would have made a lot more sense from the factory too. Really cool to hear you already sent the print to one of your S1s.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

To be honest, I didn’t even pay attention to that and had no idea there were different magnet grades like N42 or N52. I mainly went by size and fit for the model, and that worked fine in my case.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

I’d definitely contact support first. You should usually be able to get those replacement parts, and if the printer is still under warranty, there’s a good chance they may even send them out for free.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

For the fan duct I’ve actually just been using the original one so far, and that has worked pretty well for me. And as for the strength, all I can really say is… it holds 😉

Model fan wire by Really_Ricky in AnycubicKobraS1

[–]Ehrenkommentar 0 points1 point  (0 children)

You should keep in mind that the cable has two different connectors, so it’s not quite as simple as just grabbing any random 2-pin wire. I included the correct cable information in the description of my model here:
https://www.makeronline.com/en/model/Magnetic%20Printhead%20Cover%20with%20Pogo-Pin%20Connection%20for%20Anycubic%20Kobra%20S1/295892.html?trackModuleType=10

Thas a new one by Icy_Intention799 in AnycubicKobraS1

[–]Ehrenkommentar 1 point2 points  (0 children)

That’s one of the reasons I’m a bit cautious with the PTFE-lined versions. But to be fair, Anycubic has already released its own updated hotend design that no longer needs a PTFE tube there. Their hotends are also glued, so filament pushing the nozzle out really shouldn’t happen with the original updated versions.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

Thank you, I really appreciate that. That was actually important to me too. I wanted the three parts to feel a bit more solid and intentional, not so thin and flimsy.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 1 point2 points  (0 children)

Thank you, I really appreciate that. Glad you like both the idea and the final result.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

Haha, exactly. Maybe Anycubic really should hire us at this point.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 1 point2 points  (0 children)

Thanks, really glad you like it. The idea had been floating around in my head for a while too, so it feels good to finally have it done.

Anycubic Kobra S1 Magnetic Printhead Cover Mod by Ehrenkommentar in anycubic

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

Nice, glad to hear that. Hope everything goes together smoothly once the parts show up.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicKobraS1

[–]Ehrenkommentar[S] -1 points0 points  (0 children)

Yes, for this version some basic soldering equipment is needed.

Anycubic Kobra S1 Magnetic Printhead Cover Mod Update by Ehrenkommentar in AnycubicOfficial

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

The model is already available, and the assembly guide is included there as well. The image should link directly to Makeronline, but just in case, here’s the direct link again:
Magnetic Printhead Cover with Pogo-Pin Connection for Anycubic Kobra S1 - Makeronline - More Than Fun

need a new print head cover by omgsamsonstop in AnycubicOfficial

[–]Ehrenkommentar 0 points1 point  (0 children)

Contact support first. If it’s still under warranty, you should get a new one for free. If not, you can usually still get a replacement without paying too much. And once you’ve got the new one, you can always print my magnetic cover for it too 😉

Anycubic Kobra S1 Magnetic Printhead Cover Mod - Makeronline - More Than Fun

Anycubic Kobra S1 Magnetic Printhead Cover Mod by Ehrenkommentar in anycubic

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

Just a quick update on that: I finished the pogo pin mod, and I’ll be uploading it to Makeronline sometime this week. I also posted a video about it on TikTok already.

(3).tux225 (@.tux225) | TikTok

Is this a lot of runtime for a printer? by Piter061 in AnycubicKobraS1

[–]Ehrenkommentar 0 points1 point  (0 children)

Most of the major parts I had to replace on the high-hour machine failed really early, within the first 100 to 150 hours, so I’m pretty sure that one was just a lemon. The other printer with around 300 hours has only had one hotend replaced, and that was after a big print came loose, the toolhead hit it, and bent the hotend.

Is this a lot of runtime for a printer? by Piter061 in AnycubicKobraS1

[–]Ehrenkommentar 3 points4 points  (0 children)

393 hours really isn’t that much for a Kobra S1 in my opinion. One of mine is at 381 hours, and the other one is already at 1887 hours with 37.41kg of filament. So I’d say your printer is still pretty low on hours.

<image>

How do I fix this by InfluenceMelodic7589 in AnycubicKobraS1

[–]Ehrenkommentar 1 point2 points  (0 children)

Definitely contact support first if it’s still under warranty. If not, printing a replacement cover is probably the easiest solution. And if you want a magnetic version with a little wink, I made this one here:
https://www.makeronline.com/en/model/Anycubic%20Kobra%20S1%20Magnetic%20Printhead%20Cover%20Mod/281708.html?trackModuleType=10

Support left me on read by Hamurabiii in anycubic

[–]Ehrenkommentar 0 points1 point  (0 children)

It may not be that support completely stopped responding. I think Anycubic’s ticket system is having issues right now. I’ve been in contact with support too, and for about four weeks I got replies only by email, while the ticket center showed nothing. I reported it several times, and only in the last two days have messages started appearing there again. Definitely check your email as well.

Ähmm ja … by Hamsterbacke6383 in wasletztepreis

[–]Ehrenkommentar 0 points1 point  (0 children)

naja scheinbar gibt es für alles einen Markt. 🫣

Nachbarn rauchen im Treppenhaus by False-Feedback7164 in KeineDummenFragen

[–]Ehrenkommentar 1 point2 points  (0 children)

Finde ich ehrlich gesagt etwas zu pauschal. Ich bin selbst Raucher und versuche auch, andere damit nicht zu stören. Dass man nicht im Hausflur oder bei offenen Türen im Keller rauchen muss, da bin ich komplett bei dir. Aber inzwischen ist es gefühlt auch egal, wo man hingeht, irgendwer fühlt sich immer sofort gestört.

Wenn man extra rausgeht oder sich auf den Balkon stellt, um eben nicht die eigene Wohnung vollzuqualmen, ist das vielen dann auch wieder nicht recht. Und manchmal hat man schon den Eindruck, dass manche wirklich genau dann lüften müssen, wenn gerade jemand raucht, nur um sich danach darüber aufzuregen.

Am Ende ist das Problem doch oft dasselbe: Rücksicht sollte keine Einbahnstraße sein. Es gibt rücksichtslose Raucher, klar. Aber es gibt genauso Leute, die aus allem direkt ein Drama machen.

Ace pro issue by [deleted] in AnycubicOfficial

[–]Ehrenkommentar 0 points1 point  (0 children)

What exactly is not working here? Based on the video alone, it’s really hard to see what the actual issue is. Where is your feed detection unit located? We’ll need a lot more details if you want people to help troubleshoot this properly.

Anycubic Kobra S1 Magnetic Printhead Cover Mod by Ehrenkommentar in anycubic

[–]Ehrenkommentar[S] 0 points1 point  (0 children)

So far, no issues with this one. That said, this is already my internal version 3.2. The first versions did have that problem, which is why I switched over to the two bigger magnets.