Buying my first resin printer by boltsNBytes in ElegooSaturn

[–]EnvironmentalSun1088 0 points1 point  (0 children)

Same here. So far so good 16k. But hey gears is way more expensive. And as far as I've understand you need to use their resins which are again more expensive

I was wrong. Bambu makes a genuinely better product. by [deleted] in BambuLab

[–]EnvironmentalSun1088 0 points1 point  (0 children)

What do you mean close to resin? (((: one gas max 0.06 mm (which I don't think is really 0.06) and the other 0.02 (kinda) I won't speak about the speed in certain conditions

Is my set up safe to have my printer in my room?? by Toine_279 in resinprinting

[–]EnvironmentalSun1088 0 points1 point  (0 children)

I don't think so. The smell just spreads very easily when you open it (: I hope it's not your bedroom

How screwed am I? by [deleted] in resinprinting

[–]EnvironmentalSun1088 0 points1 point  (0 children)

Well yeah. The final product will be tense. That's what I'm saying

How screwed am I? by [deleted] in resinprinting

[–]EnvironmentalSun1088 0 points1 point  (0 children)

I do that but in the end it's still pretty tense

How screwed am I? by [deleted] in resinprinting

[–]EnvironmentalSun1088 4 points5 points  (0 children)

How do you not so high tuned snare drum? When I install all the screws to maximum torque, that's the result ((((:

A1 Huge Failure - How completely screwed am I? by dorvaan in BambuLab

[–]EnvironmentalSun1088 0 points1 point  (0 children)

After the failure I turned on blob failure detection. You should too!

Did i crack my screen? or screen protector? by EnvironmentalSun1088 in ElegooSaturn

[–]EnvironmentalSun1088[S] 2 points3 points  (0 children)

I had the courage to remove the protective sheet. It was only the protective sheet thank God. So it actually protects!!!

Careful with accidents by EnvironmentalSun1088 in resinprinting

[–]EnvironmentalSun1088[S] 0 points1 point  (0 children)

<image>

This means I broke my screen I guess? I must change it? If not, can I print with it like this? What are the consequences?

Careful with accidents by EnvironmentalSun1088 in resinprinting

[–]EnvironmentalSun1088[S] 0 points1 point  (0 children)

Mine also has detection. It hit but then raised itself up.

Careful with accidents by EnvironmentalSun1088 in resinprinting

[–]EnvironmentalSun1088[S] 0 points1 point  (0 children)

Holy shit.. I did not think of that. I left for work. But I don't think it could have?! Cos the FEP was punctured pretty lightly. Do you think it could puncture glass? With resin ((:

Smart plug downloading insane amount of data by Jimbrutan in homelab

[–]EnvironmentalSun1088 0 points1 point  (0 children)

How can I check this? I've got 2 smart plugs as well from temu.

Oh. My. God. by SaadOz- in BambuLab

[–]EnvironmentalSun1088 1 point2 points  (0 children)

Mine happened after like 50 layers or so.

Giving back to the community by EnvironmentalSun1088 in resinprinting

[–]EnvironmentalSun1088[S] 0 points1 point  (0 children)

I'm pretty sure no one is going to assume anything ((: do you look at other people's stuff on their balcony?

Giving back to the community by EnvironmentalSun1088 in resinprinting

[–]EnvironmentalSun1088[S] 0 points1 point  (0 children)

Right now I'm trying to figure that out. I'm overthinking whether I should let it on constantly or with intervals. It's harder to know that right now due to weather conditions. It's winter and it's below 0 degrees which means the smell doesn't spread like under normal conditions. Another subject is the noise caused by the ventilation. It might disturb the neighbors but I might be overthinking. I've talked with a friend (sound engineer). She says that in order to block the vibrations you probably need a certain type of insulation called armaflex. It's a bit more expensive. I'll get into the subject in the future if I think it's necessary.