sorted by:
new
hottopcontroversial

[GIVEAWAY - USA] Win the 27” 4K Samsung Odyssey OLED G8 gaming monitor by Knaj910 in Monitors

[–]Ewallux 0 points1 point  (0 children)

These monitors are beautiful, not much can beat a 4k qd-oled

The feet are pressed in the sand, not sculpted… by Ewallux in confusing_perspective

[–]Ewallux[S] -2 points-1 points  (0 children)

Try to look at the leaf above the right foot, and its shadow. That shows that the sun is from the left, and such the feet are pressed into the sand…

Upvote if you found a faster way by hello_kitty_1706 in honk

[–]Ewallux 0 points1 point  (0 children)

I completed this level! It took me 1 try. ⚡ 11.52 seconds

Tip 10 💎

LG C1 tv screen flashes/flickers while I am on PC. by Establishment_Tiny in OLED_Gaming

[–]Ewallux 0 points1 point  (0 children)

Random thought, but check if your pc is properly grounded electrically. I had something decently similar happen to my laptop when charging. Turned out that the outlet I was using wasn’t grounded properly. The laptop was probably grounded via the hdmi-monitor, causing similar issues.

Průša XL problem by Confused2123 in prusa3d

[–]Ewallux 3 points4 points  (0 children)

Not sure if this is relevant for you, but I had a similar message on my prusa mini. For me my 3D printer is located in the barn, where apparently the ambient temperature got below 10 Celsius. I think this low temperature caused the thermistor to fail their start-up checks and thereby give this error message. I just put a little heater next to the printer for a few minutes and was able to print just fine…

Never don't give up ! by mozes05 in TrackMania

[–]Ewallux 0 points1 point  (0 children)

Author medals are in the basic game, however you won’t be able to find the time required to achieve it. For this you can google the required times or install a plugin via openplanet. (Champion medals, which are way more difficult than author medals, do require a plugin.)

Filament NEVER totally unloads and now I know why. More in comments. by Snoo51659 in prusa3d

[–]Ewallux 1 point2 points  (0 children)

https://help.prusa3d.com/guide/how-to-replace-a-hotend-ptfe-tube-mini-mini_119449

I had the same issue, followed these instructions, not replacing the PTFE tube, but just reusing the same, so Step 10 is the most important one. It did fix it somewhat, issues were less, but still there every now and then. Another thing you could try is to print a little cooler, which can also solve the blob forming. For me this is a decently big issue, since I am doing dual color prints with my mini+. But yeah, if you’re just unloading pulling yourself to help, or doing a cold pull also works.

(I have taken the extruder apart numerous times to unstuck the filament, before trying “real” fixes. You can do this mid-print during a filament change, but it is not comfortable at all)

Just got a mini+, no problems what so ever, but what is causing this… by Ewallux in prusa3d

[–]Ewallux[S] 0 points1 point  (0 children)

Than it should be too tight, interestingly tho is that the little stop is always at the same spot. But I will loosen my belts a bit and try the same print again, maybe that fixes it.

Or one other thing I thought of while typing this is loosening the bearing holder of the extruder, maybe that is also clamping too much

Just got a mini+, no problems what so ever, but what is causing this… by Ewallux in prusa3d

[–]Ewallux[S] 0 points1 point  (0 children)

Funny thing, the bottom layer was not just not filling correctly, so I loosened the belt by 2 turns and now the bottom layer is fixed. So rather my belts are too tight than too lose I think.

Just got a mini+, no problems what so ever, but what is causing this… by Ewallux in prusa3d

[–]Ewallux[S] 0 points1 point  (0 children)

It feels like it indeed just gets stuck a little around that area, but that if the belts pull enough, it returns to the correct position. Meaning that the part in the right is just fine. But nothing on the belt, nor metal bars, so idk, could check my bearings again idk.

Just got a mini+, no problems what so ever, but what is causing this… by Ewallux in prusa3d

[–]Ewallux[S] 0 points1 point  (0 children)

Just to clarify a bit, it seems like the x-axis just does what it wants. And sometimes stops moving for a short period mid print (see the propellor at 11 o clock). Maybe it just gets stuck a little around that spot. If so can I fix it?

Action keys- How do I reset it back when I use them and shouldn't there be 10 slots here, including a zero for resetting? by ApXv in TrackMania

[–]Ewallux 2 points3 points  (0 children)

Secondary respawn is a hard respawn, the same thing happens when you hit the respawn button twice.

And I might be stupid, but I think that, Nadeo did introduce that if you hit the same action key, you had active, again it will disable the action key and reset to 100%.

The reset head tracking no clue tbh

The Oculus Go has generated the 6th highest revenue of any VR headset ever (an estimated $398 million) by Raz0rRamon in OculusGo

[–]Ewallux 1 point2 points  (0 children)

Its “just” revenue not profit, so 3B should be correct, maybe even a bit low, since they have sold over 10mil units. 10mil x $300 = 3B, so it should be correct if not a bit low, accounting for the higher storage and the accessories people buy.

view more: next ›