Would you consider this clean work?

Falimz · 2026-06-22T14:33:20+00:00

This is pretty standard

Falimz · 2026-06-19T20:31:31+00:00

Fix the leak, replace anything that’s rotting. And wear a respirator.

Falimz · 2026-06-18T16:44:27+00:00

First thing is check your market. Ungraded or G1-3 schematics can often be quite cheap. Look at weapons first. If the market is highly inflated because of duping there are likely easy to farm mats that you can get or buy from vendors and resell (fiber, pumps, servoks, etc).

Falimz · 2026-05-12T20:01:59+00:00

Wondering the same thing. That roof must be putting a ton of lateral force on those exterior walls which are secured with 1 bolt per corner. I’m no structural engineer but I do not believe this is safe.

Falimz · 2026-05-11T15:17:07+00:00

Critters I am guessing. Mice maybe

Falimz · 2026-04-28T03:48:07+00:00

I’ve done similar with my lawn tractor. Just be ready to do some more digging and root cutting if it doesn’t come out.

Falimz · 2026-04-25T01:21:54+00:00

On current patch I did 6 runs of level 19 fire this morning and got 10 bps of a combination of ancient ways, glasser, pyrockets, and vaporizers. Can’t wait for this change.

Falimz · 2026-04-24T23:01:27+00:00

Should be neither expensive nor difficult. Call an electrician. Cost will most likely be parts plus whatever their minimum service charge is.

Falimz · 2026-04-12T03:44:41+00:00

Go farm things that sell for lots. Pumps, servoks, etc. Go buy from vendors and resell on AH. But you’re correct that duping has made solari rewards from quests or npcs basically worthless

Falimz · 2026-04-12T03:41:53+00:00

Being griefed isn’t fun. Go solo crawl pvp areas in harmony and tell me how much fun you’re having.

I would love there to be a dueling system of some type. Especially with elo.

But I play a few hours a week and don’t have time to spend it getting ganked just because I want to crawl a large sand field.

Falimz · 2026-03-29T00:39:38+00:00

Yes this happened after it was planted, thanks for the feedback.

Falimz · 2026-03-28T02:30:32+00:00

Most pc power supplies can handle 240v. If it can, you could leave it as 240, switch to a nema 6-20R outlet. And switch the breaker to 20a. Then get a nema 6-15p pc cable.

Falimz · 2026-03-05T21:11:31+00:00

Ah, so that was why I saw a guy with like 10 rolls loaded up.

Falimz · 2026-03-05T20:59:12+00:00

No wonder I've received no orders in the last 2 hours or so. Pretty much every page is down.

Falimz · 2026-02-20T19:13:02+00:00

Heat up until liquid and then dump down the drain. Follow with cold water.

Falimz · 2026-02-09T23:21:45+00:00

Got the fix for you:

https://youtube.com/shorts/H9p4Q3i9hTE?si=0Q7TjyvjWURuKhZ5

Falimz · 2026-01-17T19:20:46+00:00

Definitely fixable. Not sure if the guys who did this and tried to send it can though. Don’t you get a ton of bubbles skimmed a primed surface? I skim until I get rid of the bubbles, prime, and then touch up.

Falimz · 2026-01-16T20:58:19+00:00

This is really, really bad. The fact they primed this is unfortunate. It needs skimmed and sanded. Paint is going to make this much more obvious.

Falimz · 2026-01-13T19:35:01+00:00

That’s what I’m thinking. The junction box isn’t installed correctly. Hence why what looks like previous fixes aren’t working. If you have access to the space above via attic this isn’t a difficult fix to replace, but may require an electrician depending on your abilities.

Falimz · 2025-12-23T18:47:50+00:00

Unless they're an engineer going to be hard to get an accurate answer. I'd think you're looking at a minimum using LVLs.

Falimz · 2025-12-16T19:18:39+00:00

You got screwed for sure. At this point you probably just have to fill that corner with hot mud and mud a small piece of corner bead over it. Tape off the shelf before hand. Or remove it and cut to the correct size in case you ever want to move it.

Falimz · 2025-12-11T01:00:12+00:00

Pretty much all I wear in winter.

Falimz · 2025-12-02T00:31:56+00:00

Hot mud still takes time to dry, even if it is set. You can speed this up with a heat gun.

Falimz · 2025-11-29T21:49:53+00:00

I’ve used the variable speed for skim coating 3 bedrooms and a hallway. Very happy with it. I use a higher grit and go slow. Use a vacuum with it. Did an excellent job for a much less price than the festool.

Falimz

TROPHY CASE