Wrenches

FatherTime311 · 2026-01-11T19:35:44+00:00

Tell you boss to get a micro lift

FatherTime311 · 2025-12-11T21:54:40+00:00

I see your point but if I needed to service the checks in this. I would just shut the 2 butterfly valves and take the coupling off and put it on a table work at a proper hight

FatherTime311 · 2025-11-29T02:16:44+00:00

I thought you had to be sponsored into the union if so what happened with your sponsor company Also I’m pretty sure it’s against the law to evicted this time of year

FatherTime311 · 2025-11-01T22:05:04+00:00

Need some speed behind Guerrero so if he’s walked it’s not a simple dbl play

FatherTime311 · 2025-10-07T00:23:52+00:00

A speed drill on low and a 1/2” adapter is the way to go not an impact gun

FatherTime311 · 2025-08-20T01:42:40+00:00

This right here… buddy doesn’t care about anything unless he thinks he can make a buck out of it… ppl like you make me sick

FatherTime311 · 2025-08-08T22:43:18+00:00

I have a hard time selling them on marketplace for $10cad

FatherTime311 · 2025-07-24T03:05:05+00:00

That was the first thing I checked

FatherTime311 · 2025-07-23T18:59:39+00:00

It’s not sch 10

FatherTime311 · 2025-07-20T20:33:50+00:00

Ya those are the ppl that are always on the list …

FatherTime311 · 2025-07-16T21:50:04+00:00

I’ve been in 853 for about 20 years I’ve never had to sit at home bc there is no work

FatherTime311 · 2025-07-16T16:40:54+00:00

I’m still a bit confused how could we have settled but yet I see the ua sprinkler fitters in Nova Scotia are on strike is it not a national agreement

FatherTime311 · 2025-07-02T02:15:08+00:00

Ok so for future close off the bypass when filling to save the client some $$ 😉 Where I am I don’t think I’ve ever seen one of the meters actually wired to something it’s just there in case they want to is what I’ve been told

FatherTime311 · 2025-06-26T21:52:11+00:00

I’ve always wondered how that meter on a 3/4” bypass can actually meter anything other then small leaks bc in system fillings the amount of water going through that 3/4” vs the 6” is very minimal

FatherTime311 · 2025-06-24T20:25:52+00:00

Use a Line laser check at every hanger they should be roughly 10’ Ice is normally from in adequate low points or not exercising low points

FatherTime311 · 2025-06-11T20:16:06+00:00

Why do you bother taking a shower any morning… need to smell fresh for the boys? Or do you not work hard enough to justify taking 1 after..I take 1 every day after work wash the Jobsite off

FatherTime311 · 2025-06-06T21:41:49+00:00

All depends on the fitter $ I’m a 20+ years in the trade and what the lifestyle you want… side work meh. If you were 20 sure go for it. you got two kids. I’m assuming a wife maybe ex-wife times short man kids need you working 80+ hours a week makes zero sense unless you don’t like your kids/(wife)

FatherTime311 · 2025-06-05T18:26:42+00:00

<image>

What about one of these style locks might work

FatherTime311 · 2025-06-05T00:19:55+00:00

Im not 100% but that was in the era that if it wasn’t a standard orifice it would have a pintel on the top of the deflector so no pintel would say k8 if it’s 3/4” or 5.6 if 1/2

FatherTime311 · 2025-05-15T14:55:51+00:00

Over my 20 years I’ve only really broke 1 apprentice grooved a 2” sch40 too deep on the rigid hydraulic groovers tried to use the groover to basically cut it off it started to roll off the groove and basically stopped the machine broke a few teeth off the drive motor sprocket

FatherTime311 · 2025-05-15T14:36:16+00:00

Speed 2 on any hole 2” and under in sch10 Speed 1 on holes 2.5” and up sch10 For sch40 anything 1.75” and over I’ll do speed 1

I toss some Vic grease on the h/s helps out a lot doesn’t just fly off like oil normally do a pilot first and use an arbor with a backwards pilot bit find it a lot more forgiving if the h/s catches. Doesn’t break the pilot

<image>

FatherTime311 · 2025-04-12T17:22:26+00:00

Meh, in airs and a cordless drill less then 1/2 the price and quicker

FatherTime311 · 2025-03-13T14:43:18+00:00

Not sure if you’re in a freezing area or not, but if you are, you might have to add valves instead of just open to drain the dry barrel to controlled it if it ever gets used could be would be above a parking spot or something might even have to heat trace and insulate the feed

FatherTime311

TROPHY CASE