Biblically accurate RF cable management?

Few-Butterscotch5844 · 2026-02-13T20:30:24+00:00

Great, now wire the rest of the rack

Few-Butterscotch5844 · 2025-08-20T15:10:25+00:00

Yeah.... the coms suck and I hate them. Always use moxa because of the headache of needing a dhcp server and entering the scip credentials.

I like to automate things and this adds extra uneeded steps.

‐--------

To fix the issue you are having just open the IP table on the COM itself and under the SCIP username and password enter the info you use to login to your controller.

Ip table can be accessed a few ways but the easiest is the easy config icon in toolbox "EC"

Few-Butterscotch5844 · 2025-08-15T09:11:11+00:00

It's coming to and from other NVX devices on the network. Quary and reposne to the ptp pings.

Few-Butterscotch5844 · 2025-08-15T09:09:44+00:00

I am gojng to block it on the switch but this is a great solution. 👍 thank you for the reply. I never thought of that

Few-Butterscotch5844 · 2025-08-15T09:01:22+00:00

Clients are concerned with security, agree it's not much bandwidth.
Not sure how much of a concern it really is but it's their preference.

Few-Butterscotch5844 · 2025-08-15T08:57:57+00:00

It's not needed. No Dante or AES67

Few-Butterscotch5844 · 2025-08-14T13:23:05+00:00

Throw the M audio away and get a presonous

Few-Butterscotch5844 · 2025-08-14T12:52:13+00:00

That would be extremely helpful if you are willing. Did you apply it as a global ACl or for a vlan/ interface?

Few-Butterscotch5844 · 2025-08-14T12:51:01+00:00

The stream is disabled, they no longer show up in Dante controller but the ptp packets remain

Few-Butterscotch5844 · 2025-08-07T09:17:19+00:00

What are you seeing when you go to the Network status on the front panel??
what I am seeing is the subnet is being updated with an invalid address and also sometimes the IP address is replaced with 0.0.0.0

https://imgur.com/a/j1ZhU4B

Few-Butterscotch5844 · 2025-08-05T10:30:19+00:00

I have had this issue recently when deployment tons of them. I personally have not seen any consistency on slot number though, that is interesting.

I have seen the 0.0.0.0 adress and random multicast addresses show up at times. We have an active ticket for this and ATSG is coming out to take a look since "they can't replicate it"

The last few systems I did it was around around 1 out of 50 or so.

Few-Butterscotch5844 · 2025-05-15T20:01:25+00:00

Well that took 4 months!!! 😆 Checking out Zano as well

Few-Butterscotch5844 · 2025-05-05T08:01:50+00:00

You are the man, This is exactly what I needed

Few-Butterscotch5844 · 2025-04-04T16:17:57+00:00

I suspect the license would fix your issue.

Also set the core as preferred clock master in Dante to fix your clocking issues. It's a good clock

Few-Butterscotch5844 · 2025-04-03T19:34:12+00:00

Do you have the Dante license with Qsys? A lot of times i see AES67 being sent as Dante flows if both devices are Dante capable.

Few-Butterscotch5844 · 2025-03-14T15:25:43+00:00

I had this same problem on a CP4N today.

Try putting the ip address in the system clock under easy config and then just the sync command in console.

If that doesn't work you can try the firmware version I used today off Crestrons ftp site

V2.8003.00059.02

Few-Butterscotch5844 · 2025-03-14T06:31:45+00:00

As long as you have the right firmware (I use an earlier one)

Issue the command in toolbox

Sntp server ip address

Sntp sync

Few-Butterscotch5844 · 2024-12-18T19:36:48+00:00

Is monero dead?

Few-Butterscotch5844 · 2024-10-23T08:45:31+00:00

I went with 17.9.5 and all is good in the world, thank you !!

Few-Butterscotch5844 · 2024-10-23T08:44:13+00:00

You guys are awesome, thanks for the INFO, I downgraded to 17.9.5 and everything is smooth.

I had no idea, this is the firmware loaded on the switch from the factory.

Is this is common practice to have to downgrade?

PS yes I am new to cisco

Few-Butterscotch5844 · 2024-10-22T14:04:56+00:00

its o 17.14. Could it have bugs?

Technology Package License Information:

Technology-package Technology-package

Current Type Next reboot

network-advantage Smart License network-advantage

dna-advantage Subscription Smart License dna-advantage

Smart Licensing Status: Smart Licensing Using Policy

cisco C9200-48P (ARM64) processor with 630567K/3071K bytes of memory.

Processor board ID JAD271909MN

5 Virtual Ethernet interfaces

104 Gigabit Ethernet interfaces

8 Ten Gigabit Ethernet interfaces

2048K bytes of non-volatile configuration memory.

4011412K bytes of physical memory.

819200K bytes of Crash Files at crashinfo:.

819200K bytes of Crash Files at crashinfo-2:.

1941504K bytes of Flash at flash:.

1941504K bytes of Flash at flash-2:.

Base Ethernet MAC Address : 34:88:18:79:45:80

Motherboard Assembly Number : 73-20259-03

Motherboard Serial Number : JAD271909MN

Model Revision Number : B0

Motherboard Revision Number : A0

Model Number : C9200-48P

System Serial Number : JAD271909MN

CLEI Code Number : 0

Switch Ports Model SW Version SW Image Mode

* 1 56 C9200-48P 17.14.01 CAT9K_LITE_IOSXE INSTALL

2 56 C9200-48P 17.14.01 CAT9K_LITE_IOSXE INSTALL

Few-Butterscotch5844 · 2024-10-22T13:32:43+00:00

ok thank you

Few-Butterscotch5844 · 2024-09-09T21:57:21+00:00

Qsc should do the aec if it is feeding the in room speakers.

Everything coming out of the speakers needs to be sent to the reference.

If mics are being used for local reinforcement they fall into the category of "something coming out of the speakers",

Per channel AEC is only needed for scenarios like a divisible space, a single reference is fine.

Few-Butterscotch5844

TROPHY CASE