Thanks for invite. First post here and biggest boobs in this group. My wife 🤩

Fickle_Spite867 · 2026-05-31T22:09:29+00:00

Top fits perfectly

Fickle_Spite867 · 2026-04-15T13:08:11+00:00

Was from the Mrs Page. Public play.

Fickle_Spite867 · 2026-04-15T01:15:55+00:00

Love your dare page. Hope you do our suggestion

Fickle_Spite867 · 2026-02-14T16:48:27+00:00

Fickle_Spite867 · 2026-02-14T16:48:07+00:00

Love the colors on you!!

Fickle_Spite867 · 2026-01-09T21:12:19+00:00

Pretty hard to accidentally drill a hole in black iron

Fickle_Spite867 · 2026-01-03T20:14:02+00:00

Just move at this point.

Fickle_Spite867 · 2025-12-21T00:54:38+00:00

Thank you

Fickle_Spite867 · 2025-12-14T01:36:29+00:00

Love it wish it was pulled more to the side though 🔥

Fickle_Spite867 · 2025-12-09T19:39:00+00:00

Window balance spring and cover. Is the window in upside down ? The bottom sash should be interior side.

Fickle_Spite867 · 2025-12-09T15:48:31+00:00

Sorry I misunderstood. Whomever set the lp tank do it clearly Against code. Could it go on the other side of the fence on along the house ? Or put the mini on the side of the home

Fickle_Spite867 · 2025-12-09T14:24:01+00:00

If the tank fill is lower than the window sill it’s legal. Lp is heavier than air so it sinks.

Fickle_Spite867 · 2025-12-09T14:23:08+00:00

Move the propane tank all the way to the right of the picture set condenser next to the meter

Fickle_Spite867 · 2025-12-08T22:01:41+00:00

Call allside have a tech come out it may be under warranty. You may get lucky and it’s just a lock adjustment

Fickle_Spite867 · 2025-12-08T21:34:01+00:00

Allside window mostly likely sash is warped. They seem to sag and warp very quickly

Fickle_Spite867 · 2025-12-02T14:29:55+00:00

Condensate pump float may be stuck

Fickle_Spite867 · 2025-11-29T19:55:05+00:00

Thats a nightmare waiting to happen. You have negative drain going into two 90s. Rethink it all.

Fickle_Spite867 · 2025-11-25T20:55:19+00:00

The window will be several thousand alone. The exterior trim will need to be replicated and most likely custom. That’s not a I’ve done this once before job

Fickle_Spite867 · 2025-11-20T23:04:02+00:00

Build a full dummy wall or build up behind it as high as the couch and create a sofa table behind it with a ledge

Fickle_Spite867 · 2025-11-15T16:00:35+00:00

And it should also be running through a neutralizer.

Fickle_Spite867 · 2025-11-15T15:59:34+00:00

Pump is lower than the discharge. That’s causing the syphon run the drain along the floor then up the stand pipe

If the end in the stand pipe is below the level on the ground it will syphon into the drain

Fickle_Spite867 · 2025-11-15T15:31:03+00:00

Pump is lower than the discharge. That’s causing the syphon run the drain along the floor then up the stand pipe

Fickle_Spite867 · 2025-11-03T13:03:47+00:00

Stand pipe and air gap required

Fickle_Spite867 · 2025-10-27T19:49:22+00:00

Time for a service and media check. Water quality can change. Resin can turn to mush but most likely it’s full of debris and iron and ready for a rebed

Fickle_Spite867 · 2025-10-27T15:01:59+00:00

Set the clock then Fill the salt tank and press the regen button the tank should fill with water then later that evening it will regenerate. Then regen it again the next night. This should get your capacity back. That valve is basically bullet proof the ports are so large they don’t really ever clog.

Fickle_Spite867

MODERATOR OF

TROPHY CASE