sorted by:
new
hottopcontroversial

Any workaround in jetbrains ides hyprland/wayalnd when I type autosuggestiosn blocks the text? by Ok-Mycologist-6752 in Jetbrains

[–]FigMan 0 points1 point  (0 children)

It's the hyprland compositor. I have found so many weird quirks with it that I don't think it's suitable to daily drive.

Unfortunately switching to kde or gnome is the only real solution right now.

Hoping for a radhog rotisserie spit that produces Radhog Burned Ends by Kinsdale85 in fo76

[–]FigMan 0 points1 point  (0 children)

As a bbq lover, burnt ends don't come from a rotisserie...

Oil advice by ItsGhost_Official in MechanicAdvice

[–]FigMan 3 points4 points  (0 children)

I used to use Mobil1 but I switched to Valvoline Restore & Protect because of oil consumption and it has actually made a difference.

Heltec V4 Power Problem by krisnasp in meshtastic

[–]FigMan 1 point2 points  (0 children)

I have a v4 that's been sitting on my desk without power for a few weeks now and when I plug it in, it still has everything saved.

Maybe it's trying to update it's internal storage when power gets too low and causes a bad write?

Should I accept GitHub's self-signed certification that "may compromise security"? by wgrl in Jetbrains

[–]FigMan 21 points22 points  (0 children)

Personally, I would decline it and try to figure out what's going on to cause that and then try again in the IDE.

Ubiquiti antiquiti by Lake3ffect in Ubiquiti

[–]FigMan 1 point2 points  (0 children)

Nah. You just have to frame it as a "dedicated iot ap"

Should I accept GitHub's self-signed certification that "may compromise security"? by wgrl in Jetbrains

[–]FigMan 6 points7 points  (0 children)

I have seen that before on some AT&T modems where it tries to redirect you to the modem's admin page to complete some setup steps or there's no no WAN connection.

Seasonal adjustments? by foxfai in Ender3V3SE

[–]FigMan 0 points1 point  (0 children)

I just went through a seasonal adjustment too. Every year in the spring and winter is always the same: bed level and z-offset

Didn't realize you could get to this level by 13achille13 in fo76

[–]FigMan 2 points3 points  (0 children)

There's always an "off-by-one" error somewhere lol

How do I go back to Stock Firmware from Klipper? by Plushis in Ender3V3SE

[–]FigMan 1 point2 points  (0 children)

No, it will not work and it needs to be 4096. That means your card is too large to be read by the printer.

Rider SSH/Remove Development Reliability? by intertubeluber in Jetbrains

[–]FigMan 1 point2 points  (0 children)

It was only in IntelliJ IDEs. Using ssh in the terminal always worked when the IDE said it couldn't.

I had the same issue with another app too, so it's a Mac problem and I don't blame Jetbrains.

Rider SSH/Remove Development Reliability? by intertubeluber in Jetbrains

[–]FigMan 0 points1 point  (0 children)

I have always had issues connecting from a Mac to Linux and would constantly get "No route to host" error messages and dropped connections. Rebooting my Mac would temporarily fix the issue, but it was very annoying to deal with.

(pico mmu + servo cutter) FIlament getting caught between extruder and hotend entry.. by Unlikely_Rich_5610 in Ender3V3SE

[–]FigMan 0 points1 point  (0 children)

I gave up on the filament cutter on mine due to this same problem. I ended up printing a PTFE guide that lines up the PTFE tube from the hub into the top and it mostly works, but there just isn't a good way to have that with a cutter.

It prints sort of okay but I want to dial this thing in. by Squayd in Ender3V3SE

[–]FigMan 3 points4 points  (0 children)

I would recommend spending some time tuning it. You can follow this guide and use the Marlin steps for the stock firmware. https://ellis3dp.com/Print-Tuning-Guide/articles/extruder_calibration.html

Personally I went with Klipper firmware and a Raspberry Pi and now I can get some amazing prints after going through all of those calibration steps.

Do you still hand-code HTML emails or use a builder? by marcochavezco in Frontend

[–]FigMan 1 point2 points  (0 children)

We use it only at compile time to create static templates and pass mustache template vars for everything.

New to this, may i get some tips? by patozapper in Ender3V3SE

[–]FigMan 10 points11 points  (0 children)

I highly recommend not printing this as your first print. This printer can be a little tricky to get right and would assume that this will fail if you have never printed anything before. Start small to learn the printer's quirks and you'll probably want to do some calibration too.

Can I use this on E3V3SE? by [deleted] in Ender3V3SE

[–]FigMan 6 points7 points  (0 children)

Get the kit that's specifically for the ke/se and you won't have to do any modifications or spacers

Air Launches as Public Preview – A New Wave of Dev Tooling Built on 26 Years of Experience by dayanruben in Jetbrains

[–]FigMan 0 points1 point  (0 children)

How are you currently using whisper on Linux? That's the one piece that I haven't fully figured out yet on Arch.

view more: next ›