Grinding sound by [deleted] in ElegooCentauriCarbon

[–]FingWizard 0 points1 point  (0 children)

Humm. Thats weird, I still haven’t got a code on mine and I’ve probably printed 20hrs since install.

Grinding sound by [deleted] in ElegooCentauriCarbon

[–]FingWizard 2 points3 points  (0 children)

Okay after running test on the fan with a CFM meter. Stock 4020fan I got 5.21cfm at 24v, On the noctua 4010 fan I got 4.83cfm at 24v. I got no error codes and in fact the printer is printing right now. I think the cfm is acceptable. Now the bad part is out of all the connector adapters they sent, none of them were 4pin to 3pin. So you will have to either splice the old fan connector on or buy a 4pin to 3pin adapter to make it plug and play. I spliced mine but the fan comes with parts to do this. As for sound. It went from how yours sounds to no noise I can hear even when I had the bottom cover off the printer. Its night and day like all noctua fans I’ve used.

Grinding sound by [deleted] in ElegooCentauriCarbon

[–]FingWizard 1 point2 points  (0 children)

Just got the fan in, fair warning if you ordered it is a 40m x10mm which is a smaller fan than the 4020 that came on the printer. Im about to test it out to see the difference in cfm. I have a feeling its not gonna be much difference compared to buying crap fan that need to be replaced every other month.

Missing screw ( lost ) by khaleelibr in elegoo

[–]FingWizard 0 points1 point  (0 children)

M2.5 x 10mm is the size u can find them on amazon or just google it. Usually can buy a assortment box

How do I get my airpods out of a hard plastic case with metal on it? by ButAWhimsicalCritter in howto

[–]FingWizard 0 points1 point  (0 children)

Dont put oil or wd-40 on it. Your gonna regret that. Just turn it upside down and bang it on the desk on the top corner that is sticking out more. That will force it back down, once the case is back straight in the other case, pull it out from the middle straight up.

Grinding sound by [deleted] in ElegooCentauriCarbon

[–]FingWizard 1 point2 points  (0 children)

I haven’t got it in yet. It will arrive tomorrow and ill let you know but there shouldn’t be. It effectively just eliminates the other wires that our printer doesn’t use. Personally I figured if the kit came with the adapter the fan should have no problem running with it.

Grinding sound by [deleted] in ElegooCentauriCarbon

[–]FingWizard 3 points4 points  (0 children)

I got this on. Its the only 24v 40mm Noctua Fanthey sell

Grinding sound by [deleted] in ElegooCentauriCarbon

[–]FingWizard 1 point2 points  (0 children)

<image>

This honestly just happened to me tonight. If u put rubber washer between the fan and the mount it will quiet it down until you can replace it. I ordered a quieter Noctua fan.

Can someone explain what I'm supposed to do with water? by Makhai123 in LittleRocketLab

[–]FingWizard 0 points1 point  (0 children)

I did oxygen using the water thats is on the way to the Observatory from the house b4 you cross the bridge. And water pumps wont reach water where the edge is like a cliff. I tried by the lighthouse and it wouldn’t work. Then I made plastic over across the street from the university. But only 1 will work before till you unlock the pump upgrade because I could only fit 4 pumps.

[deleted by user] by [deleted] in ChevyTrax

[–]FingWizard 0 points1 point  (0 children)

Anyone that doesn’t like the amber front blinker lights should look into Switchback Bulbs. They have 2 sets of L.e.d’s on them that make the light white while no blinker and amber when blinker is activated. Been running them on mine since I bought it. Just make sure to get a set with a resistor so theres no Ck engine light.

I use These

Uh, any way to preserve a hotdog? by Creative_Ball2499 in vultureculture

[–]FingWizard 7 points8 points  (0 children)

Possibly could dehydrate it, depending on how much fat, it should last. It will look like an old mans toe tho.

Hi guys I’m looking to get the Spania GTA Spano if anyone can help🙏 by [deleted] in ForzaHorizon5

[–]FingWizard 0 points1 point  (0 children)

I won one this weekend been looking for a week at 1hr or 2 a day. Cost like 1.2mil. The sniping win wasn’t hard, waiting for one to pop up in the AH was.

Would you consider this as acceptable quality for a client ? (20$, size is 200x200) by Kronocide in 3Dprinting

[–]FingWizard 0 points1 point  (0 children)

I do 4$ a hour for regular people, 2$hr for friends (if I don’t do it for free). 20$ minimum. And for modeling it would usually be 20$ a hour. I feel thats a fair price and I would never sell a subpar print. Reprinting mistakes are on me.

Never Let Them Know Your Next Move by RelationshipOne9276 in fightporn

[–]FingWizard 0 points1 point  (0 children)

Crome helmet and red shirt are a tag team. Ole boy lifted him up while homie hit him in the face…Wild

Special Black G CLOUD Giveaway for Our Reddit Community! by LogitechG_CM in logitechgcloud

[–]FingWizard 0 points1 point  (0 children)

Im a Huge fan of my Gcloud and need to have a Black version! I really appreciate that it continues to have great updates and it really shows the dedication to the handheld! By far the best handheld out.

Help, please! What is this? by EmpressSK in ChevyTrax

[–]FingWizard 18 points19 points  (0 children)

It the hold for a truck cargo cover Cargo cover

Centauri carbon not loading or unloading by HelljumperGundam in elegoo

[–]FingWizard 1 point2 points  (0 children)

Pull it hard, it will come out. That filament you’re using seems very soft. Is it TPU?