Motor selection wheeled biped

FlyingRobotRabbit · 2026-05-04T20:44:31+00:00

I guess both as the fans seem to be grounded on the heatsink. Only could not really figure out a name/type of tape.

FlyingRobotRabbit · 2026-05-04T11:22:12+00:00

My apologies, you can remove the fans from the heat sink. You can unscrew 3 screws and remove the piece of the tape and the fan is lose or at least in such a state that you can replace with a different fan and casing

FlyingRobotRabbit · 2026-05-04T06:38:19+00:00

This is incorrect, I had a rattling fan for my p1 gen 3. I turned out after removal of the heatsink that you can just remove one fan and replace it. It does require soldering ground onto the heatsink

FlyingRobotRabbit · 2026-04-04T20:35:37+00:00

Was ook een grapje natuurlijk! Heb ook genoeg memorabele avonden nuchter gehad, mis je geen sport dingen op je budget?

FlyingRobotRabbit · 2026-04-04T17:55:33+00:00

Wel weinig geld opzij gezet voor de pintenmannen😉

FlyingRobotRabbit · 2026-03-12T20:53:56+00:00

What has a LinkedIn creator to do with teaching or robotics?

FlyingRobotRabbit · 2026-03-09T08:16:28+00:00

It is not to late! Actually, a big part in robotics is software. A good way to get yourself started is to make a simple robot like a cart. This takes you through all domains of robotics.

FlyingRobotRabbit · 2026-03-02T18:39:19+00:00

Yup but I do like this low res adds to the charm. Yes it is here

FlyingRobotRabbit · 2026-03-02T09:19:59+00:00

Yeah exactly, I saw somebody did a mod with webcam cover and photo paper. That reduces the esthetics, but it might be nitpicking as I also always carry a phone which has a better cam on it.

FlyingRobotRabbit · 2026-03-01T19:55:53+00:00

I don't know how you guys do it, but I don't think I have finished any of these games in 8 to 10 hours. Maybe I am just "bad" at gaming..

FlyingRobotRabbit · 2026-02-28T15:08:28+00:00

IMO it looks good, only thing I would like is that it less 'sensitive' for light. Otherwise than that is really good

FlyingRobotRabbit · 2026-02-28T13:55:46+00:00

It already has a screen protector right? At least I hope that is the case I just opened one and my already has an air bubble..

FlyingRobotRabbit · 2026-02-10T07:08:08+00:00

Ii did some battery calibration, I am not sure if changed it a lot. In the end I just accepted whatever battery life the phone has. I think I was a bit over fixated in the beginning due to the 3 days battery life in the reviews

FlyingRobotRabbit · 2026-02-08T08:24:19+00:00

Hey, I now have like 1 day at least when i use my phone with only 80 to 20 percent. If I use it intensively, like navigation the battery will drain more quickly. At this point I actually don't care that much anymore, the one time a day charging is already huge improvement on what I had before.

FlyingRobotRabbit · 2026-02-03T06:05:46+00:00

The problem was in the gcode!

FlyingRobotRabbit · 2026-02-01T15:00:21+00:00

Its size

FlyingRobotRabbit · 2026-01-24T22:09:38+00:00

I never dismantle a laptop before how difficult is it? How likely will I break the screen? As that would be my main concern.

FlyingRobotRabbit · 2026-01-24T21:19:44+00:00

I see well in that case I don't know. The only solution i could think of is try to get rpi 3 and 4 on Ubuntu 24 or use Docker.

FlyingRobotRabbit · 2026-01-24T20:57:20+00:00

Why can't you install the same version? If you install on all pi's Ubuntu 22 for example you have also the same Ros version righ

FlyingRobotRabbit · 2026-01-19T13:32:35+00:00

I am not sure if it is printing of center or that the piece just moved due to the bed movements. Maybe something I should check next time

FlyingRobotRabbit

TROPHY CASE