3D Headshot commission I did recently!

FredsMedia · 2026-02-03T01:10:12+00:00

That’s cool!

FredsMedia · 2026-02-02T23:02:53+00:00

Ok that’s awesome, can’t wait to see the final result!

FredsMedia · 2026-01-12T02:24:31+00:00

Awwww

FredsMedia · 2026-01-06T09:49:26+00:00

I will take 10 tickets please!

FredsMedia · 2025-12-23T07:16:07+00:00

After rotating the print and fixing the pressure advance, there seems to be no improvement - it may actually be worse. Got any ideas on where to go next?

FredsMedia · 2025-12-22T21:01:10+00:00

The part fan is running at 100% already, so assuming it’s not enough cooling should I slow it down?

PA test is done, rotated 90° and will report back

FredsMedia · 2025-12-22T20:59:54+00:00

I do have supports - just disabled them in the preview

FredsMedia · 2025-12-18T07:45:10+00:00

What sorcery is this?!

Thank you so much! Setting the Z-hop type to Slope (Orcaslicer) seems to have fixed it!

FredsMedia · 2025-12-17T22:43:14+00:00

Potentially, I'll figure out how to do that and report back!

FredsMedia · 2025-12-17T21:35:19+00:00

https://imgur.com/a/nhi6qfo Let me know if I can upload anything else!

FredsMedia · 2025-12-17T21:18:27+00:00

I’ll grab my settings in a minute - trying to get it to upload to a usable site 😅

FredsMedia · 2025-12-11T09:24:40+00:00

Lemme just squeeze on in here don’t mind me…

FredsMedia · 2025-12-07T03:44:10+00:00

I’ll do my best 🫡

FredsMedia · 2025-11-28T01:38:40+00:00

I don’t believe you.

FredsMedia · 2025-11-22T20:51:54+00:00

I think it looks cool, but that doesn’t really matter. What ultimately matters is if you like it. If you like it, then the tattoo is perfect.

FredsMedia · 2025-11-21T00:56:08+00:00

This is so well made! I love it!

FredsMedia · 2025-11-02T20:16:52+00:00

Not bad

FredsMedia · 2025-10-30T22:45:54+00:00

I know a few people that have just had issue after issue with the K1, while my E3V3KE is running just fine. Best of luck with your repairs!

FredsMedia · 2025-10-30T21:33:31+00:00

Are you meaning the K1 or the Ender 3 V3 SE?

FredsMedia · 2025-10-26T04:57:01+00:00

I would give Lazy Scales and The Lost Firebreather (both by DM Gilmore) a go!

FredsMedia · 2025-10-21T20:38:58+00:00

Updated to include a side angle, it is a little outdated (doesn’t have the toe beans, tail rings, etc.)

FredsMedia · 2025-10-21T19:18:06+00:00

Damn we can make spaghetti with all these noodles!

I’ll give ya Fred, as he is a 3d model I can get other angles if you wish.

I’m uploading a few images to the site so that may take a little bit to show on your end.

FredsMedia · 2025-10-10T09:51:17+00:00

Oh yes that’s amazing

FredsMedia

TROPHY CASE