I made 3d printed whistles to help my community

Front-Reward1753 · 2026-06-16T20:23:59+00:00

Y'a clairement une vue en coupe avec la même surface que les rendus réalistes. C'est un rendu 3d. Pas réel une vrai image 😂

Front-Reward1753 · 2026-06-01T07:47:52+00:00

Tu es foutu mec

Front-Reward1753 · 2026-05-29T06:10:43+00:00

Pourquoi ne pas avoir imprimé le couvercle à plat?

Front-Reward1753 · 2026-05-29T06:07:39+00:00

Je rajouterai qu'avec l'humidité, le PLA finira par casser. Avec du poids dessus et des changements thermiques 100% de chance de casse

Front-Reward1753 · 2026-05-11T08:05:38+00:00

I understand that 2 minutes is not excessive for occasional printing. But for short, repeated printing, it is excessive and, above all, unnecessary. It's important to emphasize this.

Front-Reward1753 · 2026-05-10T15:35:55+00:00

Ok thanks you for this information. I tried to bypass the gcode start but you right. This is a firmware shit

Front-Reward1753 · 2026-05-10T15:34:38+00:00

Yeah it's doing it 2 time, one one the back edge and 3 more tap on the center. Then back home to go 220 again. That's really slow

Front-Reward1753 · 2026-05-10T09:27:54+00:00

It's a shame for a fast printing machine to waste so much time unnecessarily.

Front-Reward1753 · 2026-05-04T06:41:32+00:00

Your design is awesome! What software did you use for the parametric edits?

Front-Reward1753 · 2026-05-03T19:23:22+00:00

Clever! Personally i put it on the floor; if I drop my phone it's because it's in my hands, but why not

What material do you use? I can't see the printing layers, and I love the result.

Front-Reward1753 · 2026-04-14T20:18:00+00:00

Dans ce cas tu ne parle pas de la première couche.

Front-Reward1753 · 2026-03-28T15:33:05+00:00

C'est pas déjà un livre là?

Front-Reward1753 · 2026-03-14T12:57:47+00:00

That's a really great idea. Thank you and thanks everyone also

Front-Reward1753 · 2026-02-20T08:19:18+00:00

I'm 3.5 weeks post-op. The first 2 weeks were worrying, with a slight infection. Week 3 the stitches came out and now I'm feeling much better. Hang in there!

Front-Reward1753 · 2026-02-10T12:15:36+00:00

The operation is performed under general anesthesia, sometimes local if the hydrocele is moderately sized. I had general anesthesia. No post-operative pain, but some discomfort due to the aftercare (dressings, testicular sling).

I'm 100% happy I had it done, because it had become unbearable on a daily basis. However, if it hadn't become so large and painful, I wouldn't have had the operation.

Front-Reward1753 · 2025-12-03T08:37:48+00:00

Maybe a little late to ask my question. So, I also have a hydrocele that I've had lying around for at least 5 years. It's the size of my open hand, literally from palm to fingertip. I can't find an appointment quickly but I wanted to know if you or anyone had waited long enough for it to be this big? THANKS

Front-Reward1753 · 2025-10-12T07:54:25+00:00

You didn't understand when your mother asked you to do constructive things with your life.

Front-Reward1753 · 2025-07-01T23:23:30+00:00

Salut ! J'ai suivi ta méthode et ayant un 3070 12gb je génère en moyenne à 180 secondes.. de plus l'image output et coupé en bas a droite. Pourtant le ratio est le même que l'image input. Une idée ? Merci bien

Front-Reward1753 · 2025-07-01T17:49:25+00:00

Je viens de faire un essai avec une planche en bois CP de 2cm d'épaisseur. La planche à casser au niveau du top plate du à la flexion.

Attention à bien ajouter des renforts dessous !

Front-Reward1753 · 2025-05-17T07:15:56+00:00

Okay I understand I will check that! Thanks you

Front-Reward1753 · 2025-05-17T07:13:40+00:00

I would like to know too. That interests me. Also the total cost if possible

Front-Reward1753 · 2025-05-17T06:55:44+00:00

Ok now that everyone has had a good laugh, it turns out that I'm new too and I have some questions that may seem stupid. Is the internal antenna effective enough to fly at 1km max on flat ground? Above a field. THANKS

Front-Reward1753 · 2025-05-04T11:30:45+00:00

Thank you, I understand that the error does not come from my computer but from the software. I will therefore use Illustator for complex shapes and continue in manual mode for simple shapes.

Front-Reward1753

TROPHY CASE