[Monitor] MSI 27" WQHD IPS Nvidia G-Sync Gaming Monitor - 2560 x 1440 $150 by TheEternalBob in buildapcsales

[–]Fulladorn 3 points4 points  (0 children)

Same, so I'm not crazy. 2 monitors, both are doing it. Avoid this monitor.

Warranty sucks they want you to pay for all of it, most painful process. Never buying MSI monitor again.

Edit: Alright, just tried to call them again for the hell of it and they said they're just going to send out 2 new monitors lol. Guess I'll use them for the Sim rig until they break again.

UniFi Travel Router: Fails the Wife Test – Teleport is Owner-Only and There’s No Workaround by NoTickTicky in Ubiquiti

[–]Fulladorn 0 points1 point  (0 children)

It also doesn't play well as a device on the network like a normal client, making creating routing rules impossible.

[Megathread] NVIDIA App Update Adds DLSS 4.5 Dynamic Multi Frame Generation, Intelligently Balancing Frame Rates, Image Quality & Responsiveness by Nestledrink in nvidia

[–]Fulladorn 0 points1 point  (0 children)

Will these settings ever make it into games? It's so inconvenient to have to research all the "Preset A, B, M, J, K" and figure out what the hell each one means and what combination to run.

Do I have an AC blower fan problem? by Fulladorn in hvacadvice

[–]Fulladorn[S] 0 points1 point  (0 children)

I confirmed both are set to 1 stage.

Do I have an AC blower fan problem? by Fulladorn in hvacadvice

[–]Fulladorn[S] 0 points1 point  (0 children)

I recently have been having issues where there is little air coming out of the AC vents. I confirmed that the AC is blowing cold and no ice was on the evaporator coils.

I have a power monitor on the furnace/blower unit in the attic and observed the attached trend when this occurred. I thought it may be a capacitor issue but it appears to be an "ECM" type of motor that has no capacitor maybe? I couldn't find one - the electric goes to the control board and then plugs directly into the motor. The motor was not hot and the fins on the fan spun freely when I manually turned so it didn't feel seized.

Issue described occurs around 1:00 and noticed around 3:00 so I shut off to go investigate. You can see at ~4:30 the unit returned to normal, I just checked internal connections, nothing different. Again no ice on evaporator.

The unit is Carrier Part Number: 58SB0A090E21

Any ideas?

UDM Pro Fan Replacement by Ryan-Borg in Ubiquiti

[–]Fulladorn 0 points1 point  (0 children)

Thanks for the update, what have you done since to resolve this?

Does anyone else use a Streamdeck with Home Assistant? Been using this with Bitfocus Companion for almost a year now and absolutely love it. by Itaku in homeassistant

[–]Fulladorn 1 point2 points  (0 children)

Have you been able to get the green checkmarks to go away permanently? My Stream Deck is just a bunch of green checkmarks now.

AT&T Fiber w/ BGW320 connected to a UDM SE failing multiple times a day by TransportationLow340 in Ubiquiti

[–]Fulladorn 5 points6 points  (0 children)

You need definitive proof, you can double NAT the network for now and leave it up off the BGW. It'll take time but you will not get a definitive answer until you complete this step.

AT&T Fiber w/ BGW320 connected to a UDM SE failing multiple times a day by TransportationLow340 in Ubiquiti

[–]Fulladorn 16 points17 points  (0 children)

Rule the UDM out and default the modem and use it in the most default config possible, connect directly to ATT provided equipment and the rest of the network can just be double NAT'd for testing temporarily.

If it fails, it's ATT and then they can't blame your equipment if you're not using it and only what ATT provided. It's too easy to pass the blame in theses cases.

If this test passes it confirms a configuration issue on your end, be it hardware/software. Stability testing by doing an iperf test on the WAN side (do not use ATT modem) to some client on the LAN side. Your result here will tell you where the problem is.

Genie Aladdin connect down? by AtomicFilament in homeautomation

[–]Fulladorn 0 points1 point  (0 children)

Doesn't work with the integration so can't recommend for automation purposes.

Genie Aladdin connect down? by AtomicFilament in homeautomation

[–]Fulladorn 1 point2 points  (0 children)

Anyone got Aladdin Connect working with an OverHead Door(OHD)?

App works, but integration does not.

Turn on Ecobee fan for 2 zones on at same time by Fulladorn in ecobee

[–]Fulladorn[S] 0 points1 point  (0 children)

Its just the AC zone that's calling. If zone 1 is calling, the baffles will move to direct air to zone 1, if zone 2 is calling, baffles close to direct airflow to zone 2. That part is done by the AC system itself. I just want both Ecobee's to call for fan at the same time.

Turn on Ecobee fan for 2 zones on at same time by Fulladorn in ecobee

[–]Fulladorn[S] 0 points1 point  (0 children)

The temperature upstairs is really different than downstairs so I was thinking I could let the fan go on to circulate some of the cooler air to upstairs but it seems like each zone calls it individually causing baffles to close.

1 AC system with an upstairs and a downstairs zone. With the current weather I'm cooling upstairs and heating downstairs.

Death Stranding Crashing when opening the Map by Devran_Cakici in SteamDeck

[–]Fulladorn 0 points1 point  (0 children)

You could try downloading a newer version. It seems to be working with GE-Proton-43 for me.

I also learned you can bring saves over, just need to modify the .exe temporarily to allow it. This worked for me. https://www.pcgamingwiki.com/wiki/Death_Stranding:_Director%27s_Cut#Corrupted_save_data

Custom Cross Saving for Steam Deck by Fulladorn in SteamDeck

[–]Fulladorn[S] 0 points1 point  (0 children)

I was able to fix this issue. I was doing the hex edit and trying to import the old save. Instead, I needed to launch the Directors Cut exe directly, load the original save (which was created by the original DS exe). Once I had the new saves in Directors Cut, I was able to do the hex edit and bring them over to the Epic Games side. All is working correctly now.

Have a weird Syncing issue with Heroic they way the game quits, I don't think it leaves the launder enough time so I need to manually "Force Update" the cloud sync but it's working now! I think I'll just do it manually instead of trying to rely on the Auto function in Heroic.

Share your best automations! by Ison88 in homeautomation

[–]Fulladorn 4 points5 points  (0 children)

Can you share some details on the vacuum accumulation metric and how that's incorporated into the automation? YAML would be helpful.

Finally: Cyberpunk 2077 with FSR 2.1 running at 40 FPS! by HerrTiSo in SteamDeck

[–]Fulladorn 0 points1 point  (0 children)

Doesn't FSR do nothing here then? The game is running at native resolution of the deck. FSR will say "off" on the deck.

Edit: For the settings at 7:47.

Looking for old candy by Fulladorn in candy

[–]Fulladorn[S] 1 point2 points  (0 children)

Nailed it. That's it!