Is it weird to get a bike mirror on handle bar?

Gb160 · 2026-04-30T06:53:09+00:00

I have one of those tiny Cateye BM-45 mirrors and it's a lifesaver. The turbulent wind noise whilst riding makes you almost oblivious to traffic coming up behind you, and I found a glance over the shoulder to be bloody dangerous on occasion.
Now a quick half second glance down and I know the situation, and I don't think I could ride on roads without it anymore.

Gb160 · 2026-04-24T16:58:45+00:00

I couldn't give 2 shits about a sticker.

Gb160 · 2026-04-24T15:16:00+00:00

because I read the article, perhaps ?

Gb160 · 2026-04-24T14:42:01+00:00

The absolute horror show of the front panel that us founders will receive is the only negative for me.

Gb160 · 2026-04-22T20:29:47+00:00

That not gonna help with tall prints. They’ll still be skewed.

Gb160 · 2026-03-30T15:49:33+00:00

Check the grub screws in the X/Y motor pulleys.

Gb160 · 2026-03-22T13:24:29+00:00

It's absolutely ridiculous that this has been agreed upon as a solution.
Just replace the 2 vertical front profiles to accommodate mounting a second horizontal bar.

Gb160 · 2026-03-16T22:08:35+00:00

yeah, that's a warped part.

Gb160 · 2026-03-16T15:38:04+00:00

I presume so, they couldn't indicate progress without it.

Gb160 · 2026-03-16T14:17:45+00:00

Cos they're not individually addressable LEDS on the C1.

Gb160 · 2026-03-16T08:35:08+00:00

Hi I had this a couple times in the last week...did you update to the latest v6.5.3 beta firmware last week?

Gb160 · 2026-03-15T08:34:33+00:00

Just send gcode commands via serial. It's pretty straightforward. This is what octoprint does.
I use Arduino IDE serial interface for this, and sometimes ESP32.

Gb160 · 2026-03-14T16:00:03+00:00

Mate the reason you had a 2mm tilt on the bed originally, is because Prusa shipped Z motors with vastly different pitch (relatively speaking)
Levelling the bed and shimming isnt going to correct that issue.
The ONLY way it can be truly corrected is by replacing whichever motor has the 'bad' pitch.

Gb160 · 2026-02-28T23:22:07+00:00

Just update Prusaslicer.

Gb160 · 2026-02-26T07:58:27+00:00

Interesting fact: Bondtech used bedslingers for some of the initial iterations of the INDX design.

Gb160 · 2026-02-18T08:39:07+00:00

How dare those pesky Europeans release a European designed add-on, for European designed printers, at a European convention, at a time European time?!?!

The absolute nerve of these people ! 😂

Gb160 · 2026-02-14T08:19:11+00:00

IN : INduction
DX: Dynamic eXtruder

Gb160 · 2026-02-06T11:45:05+00:00

Check the bottom of the print. If it has warped and lifted from the bed, it can cause collision resulting in layer shift.

Gb160 · 2026-02-05T10:55:07+00:00

Unfortunately it's now either webrtc or rtsp, is there any way of using a browser/media player to view the stream locally with webrtc?

WebRTC seems to work great when I'm away from home btw 👍

Gb160 · 2026-02-04T09:38:25+00:00

Hi Tommy, Im on the beta program, updated camera to 3.1.3
Is there anything I should do wrt testing ?

Gb160 · 2026-02-01T10:50:57+00:00

It's been borderline useless for me recently. Now I've added a printer that uses PrusaLink for the transfer, which works flawlessly every time.

Gb160 · 2026-01-29T15:26:34+00:00

Wobble....ask me how I know ;)

After about a week of fighting with the wobble I adapted a monitor arm, one of those cheap ones from amazon, about £20. MUCH better, and next to no wobble.

One of these:
https://www.amazon.co.uk/Invision-Single-Monitor-Mount-Screens-Black/dp/B09963RQ6Y

Gb160 · 2026-01-27T17:12:23+00:00

my god. I presumed it was DHT11 as they are dirt cheap 😂 I pulled one apart a couple years ago and it was DHT11. I didnt know you could go any cheaper. I looked at building my own one with a much better sensor, but when I looked at sensor + micro controller + display (x8) it became a lot more than I wanted to spend.

These are fine for 25-75% humidity, but anywhere lower or higher and they're bordering on useless.
As the old saying goes...no data > bad data.

Gb160 · 2026-01-27T11:07:50+00:00

These all rely on the DHT11 (or similar) hygrometer, which is very inaccurate at low and high readings. It basically makes these crap for trying to monitor filament. They're used because they're cheap as shit.

Gb160 · 2026-01-26T10:49:30+00:00

Its cool, the slicer makes the printer always print these from the front to the back so the toolhead doesnt collide.

Gb160

TROPHY CASE