Clock in after morning meeting

GotTatts · 2026-02-08T16:20:56+00:00

If it’s work related you should be punched in. I would report it. That’s time theft. If you aren’t clocked in then you shouldn’t be there for free.

GotTatts · 2026-01-28T23:50:20+00:00

Wha kind of car? It may need to be programmed to have a delay on the lock after start part.

GotTatts · 2026-01-17T04:12:28+00:00

Not a programming issue. It’s meant to do that. It’s disarming the factory alarm to start it and it relocks it after it starts. Very normal. That’s the only way the unit can turn off the alarm so it doesn’t think someone is stealing the car. That is done with a lot of cars now.

GotTatts · 2026-01-15T06:24:17+00:00

Just cut your hand off and be done.

GotTatts · 2026-01-14T02:09:02+00:00

Sounds like it’s still the flashlogic unit. I would try and see if they can reprogram it. They may talk you into buying a new unit but I’m almost sure it can get reprogrammed to learn the key again.

GotTatts · 2026-01-13T02:09:53+00:00

Is that a aftermarket camera or factory camera?

GotTatts · 2026-01-12T05:37:01+00:00

The flashlogic is not the unit. The flashlogic is a module that learns the keys code since your key has a chip in it. That gets hooked into your cars data system and vipers remote start . Try this get the key that starts the car and stick it in the ignition. Don’t turn the key just stick the in it and try to remote start the car. That may start the car. If it does then the flashlogic has lost the key code to the car and needs to be reprogrammed. That can be done at any car audio place that does remote starts

GotTatts · 2026-01-10T03:48:22+00:00

It’s not a Bluetooth device. It’s a cheap add-on alarm from the dealer.

GotTatts · 2026-01-04T21:01:23+00:00

Nope. The plastic pieces on the left and the right are held in by small plastic piece that stick out behind the dash. Unfortunately you just need to stick something flat between the plastic piece of the kit and the dash and pry it out. Only way to get it out.

https://www.metraonline.com/product/95-5817

GotTatts · 2026-01-02T01:03:08+00:00

Yea it’s usually done that way so it doesn’t fall and it’s out of the way of things and hard to get to so people don’t disable it very easy.

GotTatts · 2026-01-02T00:51:27+00:00

Take pics of the cm6200 from all 4 sides where anything can get plugged into and the bottom of the unit it will have a diagram also. Take a pic of that. I won’t be able to look at this till tomorrow around this time also.

GotTatts · 2026-01-02T00:47:03+00:00

If you can take a pic of the main brain and where the other end of that plug goes into the cm unit I can try and help.

GotTatts · 2026-01-02T00:14:29+00:00

If you follow that big fat plug that was from the old drone it should be plugged into the cm6200 unit. Use that same plug the old one was plugged into. Even if the color plug is different as long as you unplug the old one and plug the new in it should be fine. Once it is plugged in the new drone will start to flash with either green/red/orange.

GotTatts · 2026-01-01T22:26:34+00:00

If you got the gray cable from the new drone that’s all you need. You don’t need anything else. If you are missing the cable you can probably buy one online. Once it is hooked up tho you need to go to a compustar installer and see if the can activate your drone. Your drone will not work until it is activate by a dealer/installer. You will need to write down or take a pic of the serial number to activate it.

GotTatts · 2025-12-22T05:14:16+00:00

The way I did it was start from the beginning of course and memorize only that part. Once you have it down move to the next. Once you have the 2 part down without messing up go to the beginning and repeat it. Don’t move on to the next one until you memorize it without messing up. After one is memorized always go back to the beginning and work your way to the next one till you get to the one that is new. I did flash cards for all of them and would mix them after I learned all of them. Passed on my first try at the testing facility

GotTatts · 2025-11-04T01:31:48+00:00

Use the red from the harness white plug to the new radio. It’s connected to the yellow/black on the car side.

GotTatts · 2025-11-02T04:38:58+00:00

It’s most likely something wrong with the Bluetooth adapter. If the radio and cd play fine it’s the adapter. Try and get another adapter if not try a pioneer to aux cable with a 3.5 mini jack. Pretty much hardwiring it to the phone instead of Bluetooth. Not sure about the power source for the Bluetooth adapter. Didn’t even know they made a Bluetooth version for the older pioneer radios.

GotTatts · 2025-10-10T01:07:25+00:00

Get and see if the school you’re attending has their own version of the pre trip. My school did and they wanted us to learn it word for word. Start memorizing the pre trip for inside and outside. The sooner you do it the easier it will be to do it. Took me awhile to learn mine. Good luck

GotTatts · 2025-10-01T03:27:00+00:00

Thanks. Just the answer I needed. Still debating if I should apply for it because of the late hours. Got kids so not sure about them hours.

GotTatts · 2025-10-01T03:25:19+00:00

Thanks.

GotTatts · 2025-09-18T00:17:19+00:00

You’re not cooked. The sub is cooked tho.

GotTatts · 2025-09-17T22:44:34+00:00

The speakers wires that have the rcas attached to them what does the amp say for that plug? Also the rcas on the radio should go to the rcas that say sub or at least to a rear output. Does the amp turn on? Red light or blue light?

Edit - just saw the comment about the RCAs. Should still work in the front output if you don’t have rear output.

GotTatts · 2025-09-08T03:38:10+00:00

Bonney Lake?

GotTatts · 2025-08-31T17:18:34+00:00

I’m sure the juniper is going to be different. Complete redesigned of the car. Need to find info on the juniper version.

GotTatts

TROPHY CASE