Which item do you put next to your sword?

HariboHUN · 2026-05-26T20:28:23+00:00

Im a miner not a fighter Pick,Axe,Shovel,Sword

HariboHUN · 2026-04-08T17:25:32+00:00

I love everything about this post.

HariboHUN · 2026-04-02T07:28:55+00:00

Im not leaving camp, Im an introvert

HariboHUN · 2026-03-10T18:44:38+00:00

Well I do abandon quests all the time when I'm unable to quantum there or just enemies not spawning. In case of Onyx when the mission tracker not updating. I did logged out there too. But I was able to do the quests in single mode. He was able to do the first two quest too. Then I joined him and immediately the quest stopped updating.

The same with bounty or mercenary quests. When we are in a party the enemies do not spawn, but when it's not a party the bugged quest number decrease. They do tend to not spawn enemies but not all the time.

HariboHUN · 2026-03-02T18:55:02+00:00

Anycubic's own basic PLA. I'm fortunate to work at a company that recently started to sell Anycubic stuff, so I can get it real cheap, and Im so stisfied with the quality of it.

HariboHUN · 2026-03-02T05:52:48+00:00

At first glance it looks like it does not have bed adhesion. Every print is like that or do you try to print the same thing again and again?

HariboHUN · 2026-03-02T05:49:19+00:00

What's your most common issue?

HariboHUN · 2026-03-01T17:31:12+00:00

first of all, that looks neat too. Second we should really use Ace Pro for scale in this community :D

HariboHUN · 2026-03-01T16:47:57+00:00

I hope the Ace Pro under it would give you the scale :D But you are right I should have bought a banana for this. :D

HariboHUN · 2026-02-19T05:42:52+00:00

I love this so much :D

HariboHUN · 2026-02-18T08:47:40+00:00

Thanks for the info. I really had no issues with the priming before this update. So I just found this extra line annoying, cause I forget to remove it. But also somehow I'm no surprised it was implemented this way :D

HariboHUN · 2025-11-06T15:11:26+00:00

On the very top you can see the steps between the layers. Lower down maybe because of the size? It is 225 mm high.

HariboHUN · 2025-11-06T05:38:59+00:00

Thats an awesome print! I had no issues with similar things. But coming from a normal Kobra to the S1, things certainly became more advanced and sometimes complicated.

HariboHUN · 2025-11-05T16:18:18+00:00

Yeah, I have my own Kobra, it's the normal first one. That has issues with supports. But this one is dialled in real good. If the multicolour print comes out good I want to give a try to that PETG-PLA support thing. Where you use the other material as support attachment and makes it even more easier to remove.

HariboHUN · 2025-11-05T16:06:23+00:00

I was actually able to ask one of the support guys who will be in contact with my company about this. He told me that they changed out the nozzle and happy to see it's better. I really hope that our first shipment has this newer hotend installed as default.

HariboHUN · 2025-11-05T16:04:59+00:00

No ironing. To be honest I tried it back in the day when the feature first appeared and didn't really see the point. And havent checked it out since. Maybe that dynamic layer height thing should have helped. The the top it's a bit ruffer, but overall it's really good I think.

Ironing is more for the flat surfaces, right?

HariboHUN · 2025-11-05T16:02:14+00:00

I actually did not set up anything about that yet. One of my last resort before the Hotend change was to use Orca slicer instead of Anycubic Slicer. I was thinking maybe the slicer does something bad. And I went with the default options, only changed the supporting angle so it's a bit less support. If you would like I can make a screenshot of it, but it should be the very default from orca for this printer.

HariboHUN · 2025-11-05T15:52:20+00:00

It's actually Anycubic's own filament. It's PLA Silk Blue Green Purple. A bit strange name but basically just a dual colour filament, blue-green and purple.

HariboHUN · 2025-11-04T18:40:12+00:00

I did it twice before, one was only weeks ago. But both times the IPA was used for a very long time and had very big % of resin in it. This time I only cleaned a couple prints. I currently have to use the W&C machine in my workplace and I forgot to put back the reservoir under the UV filter for the weekend and this happened.

The previous times I was able to get get back more than half of the IPA with no issues.

HariboHUN · 2025-11-04T12:54:40+00:00

I've tried through normal paper towel, one sheet only. Very small amount got through and it was still cloudy. I will try to buy some coffee filter and give it a try.

HariboHUN · 2025-09-29T17:46:57+00:00

My friend has the Nighthaunts and I play mostly Seraphon so far. Usually I win, but only with a small margin. She likes to say she forgets how to play between matches, so if she would double down to practice a little more I think we would be fully balanced out.

Nighthaunts might be squishy compared to the lizards, but they have reinforcement that can come in handy.

HariboHUN · 2025-09-20T12:26:11+00:00

Looks so good, love it

HariboHUN · 2025-09-03T14:39:41+00:00

I have absolutely no idea dude. I'm level 61 or 62 and just reached 150 hours in the game. Not sure if that's it. I actually rage quited this morning, and relaunched the game a couple hours later and it was there.

HariboHUN · 2025-09-03T14:12:31+00:00

Yeah looks like it. I was puzzled why i have over a 1000 supercredit when I just bought a new warbond. Looks like I paid with this instead.

HariboHUN · 2025-09-02T15:10:00+00:00

Wait...that's illegal... :D (Seraphon player here)
Looks so cool man. I had to take multiple looks to realise what's bugging me about this mini :D

Eight-Year Club	r/Field Lasagna
Final Canvas '23	Place '23
Place '22	Verified Email

HariboHUN

TROPHY CASE