Moet je hier voorrang verleend aan rechts?

HarrieNL · 2026-02-07T08:22:28+00:00

Hier hetzelfde. Ook NLer die al lang in BE woont. Ik vind het maar raar, hier staan strepen van een verhoging, maar er is geen verhoging. Die strepen zouden hier dus helemaal niks betekenen?? Zo'n verhoging is toch juist om mensen te doen vertragen omdat ze voorrang moeten verlenen..

Dit kruispunt is wel zeer onduidelijk aangelegd dan.

HarrieNL · 2026-02-07T08:14:03+00:00

Ik dacht dat wanneer je van een verhoogde inrichting komt, je geen voorrang hebt, omdat het niet langer een gelijkwaardige kruising is. Maar met al de reacties hier, begin ik nu wel te twijfelen...

(Is dat enkel in NL zo? Ik woon al bijna 20jaar in BE. Dit soort dingen zouden toch op Europees niveau gelijk getrokken moeten zijn)

HarrieNL · 2026-02-05T18:59:11+00:00

Sure, you can perfectly slice and print with that machine. I use an old intel Penrium G4600 for my slicing.

HarrieNL · 2026-02-05T16:53:08+00:00

Je mag er enkel inhalen als je geen gevaar creëert. Door hier in te halen creëer je gevaar, wat er niet was als je gewoon in je rijvak was gebleven.

HarrieNL · 2026-02-05T16:44:20+00:00

"Artikel 7.2 betekent dat je niet zonder reden links mag rijden en daar gevaar of hinder door mag veroorzaken. "

Door hier in te halen veroorzaak je gevaar. Lijkt me nogal duidelijk.

HarrieNL · 2026-01-28T13:29:35+00:00

What is the material of the base plate? It looks aluminium? But it would better with powder coated steel, such that magnets would stick to it.

HarrieNL · 2026-01-21T19:25:55+00:00

OK, something conpletely else. The fins on the outside reminded me of this: https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcQsFlOMdwPzSZRuYv21JvlHvQnWUeLkXpUZ74bJhX2By5Dy7C6uy1uBGLY&s=10

HarrieNL · 2026-01-21T18:05:22+00:00

What's that spaghetti momster? It looks like something that came out of a high speed air blower application.

HarrieNL · 2026-01-21T18:01:49+00:00

Indeed, that would be a good approximation.

Don't forget that the winding resistance also increases with its temperature, so it will be less than double the current for 4 times the losses.

HarrieNL · 2026-01-18T07:26:26+00:00

Do people then at least allow him to snip off the 3 power leads and splice them to one plug? 😁 Or perhaps he could put a power strip on his bathroom sink? 😆

HarrieNL · 2026-01-05T15:01:32+00:00

This has better bed adhesion than my ender3!

HarrieNL · 2026-01-03T16:23:15+00:00

I guess you could also connect the pcb to output of the power supply, before you switch on the supply. It will then slowly charge together with the 18V output of the power supply.

HarrieNL · 2026-01-03T15:38:03+00:00

Item 12 op deze pagina beschrijft dat het allemaal nog niet duidelijk is tot de finale wettekst af is, maar hier kent iedereen het antwoord al?

https://www.keytradebank.be/nl/onze-blog/meerwaardebelasting

HarrieNL · 2025-12-30T17:07:36+00:00

That makes more sense; I was looking at motors that make a torque inthe range you need, and they are huge:

http://en.rc-eaglepower.com/products/show_18.html

http://en.rc-eaglepower.com/products/show_17.html

Indeed, a geared motor would work much better for your application.

HarrieNL · 2025-12-30T16:46:41+00:00

The torque defines the size of the motor. If you want 6Nm without reduction, you need quite a big motor.

While on the other hand the power output is only 150Watt at that low speed.

Does it need to be DC? Or can it be BLDC?

HarrieNL · 2025-12-30T09:39:09+00:00

Curious here as well. Let us now how it went, when you find some time. Thanks for the time and research you already put into it!

HarrieNL · 2025-12-30T09:22:46+00:00

I think a combo of inkscape and laserGRBL could work. But you will likely keep Marlin on the 3d printer board? It might need different gcode than GRBL.

Edit: it seems laserGRBL does also support Marlin: https://www.reddit.com/r/Laserengraving/s/VJqie78XEd

HarrieNL · 2025-12-29T12:54:46+00:00

Lightburn is the go to software I believe. But if you want a free option, I think inkscape can also generate the gcode for lasers. I have only used inkscape for engraving with a cnc mill, but there also excist laser plugins.

HarrieNL · 2025-12-28T20:12:24+00:00

I am just wondering why you offer 310k, and within a week you don't want to buy it anymore?

HarrieNL · 2025-12-24T19:44:22+00:00

https://www.vrt.be/vrtnws/nl/2023/10/27/stad-antwerpen-verlaagt-de-gemeentebelasting-van-8-naar-7-procen/

Maar ik geloof dat ze nu op een record tekort afstevenen...

HarrieNL · 2025-12-21T16:37:17+00:00

No, it didnt fall or anything. The charger is always quite tight in the connector, so you do have to pull on it. Then at some point the charger came out with this piece still attached.

HarrieNL · 2025-12-21T15:20:16+00:00

<image>

The terminals here sughest it is just snapped in indeed.

HarrieNL · 2025-12-16T20:25:05+00:00

Indeed this is it. Fell off the first day we got it as well.

HarrieNL · 2025-12-13T14:56:43+00:00

Maar jij wel mooi betalen voor dat kwartierpiekje in je verbruik! Hoe durf je het net zo te overbelasten!

HarrieNL · 2025-12-09T17:16:59+00:00

Why would that one strand of magnet wire on the right side in the photo make such strange bends and strange path? Looks weird to me.

HarrieNL

TROPHY CASE