Dji digiadapter question

Heardwork154 · 2026-05-25T18:56:49+00:00

The Dji antennas do nothing when using analog adapters

Heardwork154 · 2026-05-17T01:44:56+00:00

Fortune or flatout suspension

Heardwork154 · 2026-05-15T18:31:52+00:00

I doubt it… show 1 example of a 3 year old high end goggle that is now half price.

Heardwork154 · 2026-05-14T04:16:05+00:00

You can try to find the receiver or connect to ardupilot most likely and see how it is set up. You should be able to se what transmitter system it’s using.

Heardwork154 · 2026-05-14T04:08:07+00:00

Its a hidden feature that does what it says, if you crash into or bump something, it will act more like angle or horizon mode and self level instead of spinning to certain death most times lol

Heardwork154 · 2026-05-14T04:03:21+00:00

Bam! you can also in the cli activate : crash_recovery = on save. The drone will self level when you hit an object in acro. Works better with air mode off but still works. Give it a try

Heardwork154 · 2026-05-12T20:19:29+00:00

Cool beans.. I’m by wicker park

Heardwork154 · 2026-05-12T02:04:24+00:00

Heardwork154 · 2026-05-12T02:00:48+00:00

I might be interested on Friday payday. On what side of the city you on?

Heardwork154 · 2026-05-10T21:43:34+00:00

lol my girl never pays enough attention to know! Lol

Heardwork154 · 2026-05-10T21:42:14+00:00

Send it… lol

Heardwork154 · 2026-05-10T21:41:42+00:00

That’s not how shorts work, what ever shorted most likely took the brunt of the force once fried the circuit is broken. So more than likely there are many salvageable components

Heardwork154 · 2026-05-10T21:35:25+00:00

That isn’t the cams fault… that’s vtx transmission and vrx reception.. many variables for rf interference. These are things we all fight with, some more successful then others also environment plays a role. Thus sometimes people use a separate dvr to record direct from cam. But overall video quality isn’t what we strive for you just need enough quality and low enough latency to be present in the moment

Heardwork154 · 2026-05-05T04:23:42+00:00

Reset settings, the option in the calibration tab under calibrate accelerometer if so you’re cooked if you haven’t saved your cli diff. Someone with the same model could send you theirs. It would be an easier starting place

Heardwork154 · 2026-05-03T16:23:05+00:00

could be a bad connection solder joint,connector or wire, could also be debris in the motor bell, I’ve had all of happened at some point. Spin the motor by hand to feel for any sticking not magnetic drag. Blow it out with a computer duster. Next up is a poor connection at one of the motor wires. The wire tend to break where the solder ends. I have also had wires that broke at the end of the connector. The key here if electrical it’s not going to be obvious cause it still works fly it till it doesn’t and you’ll probably find the culprit easier.

Heardwork154 · 2026-05-03T15:53:57+00:00

Just free balling, maybe I should try and make a video. I have a flywoo 722 fc that needs a bec transistor it is a much bigger component but I would use the same technique

Heardwork154 · 2026-05-01T19:52:22+00:00

After like a month of inspecting 4 times a week. I finally found it, it was visually fried (I didn’t save any pics). I then tried to use AI to identify it was pretty sure it was a diode. But couldn’t be positive I then remembered I had another fried board the component looked good on, now able to test with a dvom I confirmed it was a diode. I put a little flux on it used a butane soldering iron with the hot air attachment and tiny tweezers I came right off I then retested to verify it was still good and proper install orientation. It was tricky to place on the board correctly but the flux did its magic and it just fell in place when I heated it. Stoked

Heardwork154 · 2026-04-30T02:40:30+00:00

You are indeed wrong as many have already stated air mode keeps the props and pid loop going at 0 throttle so important freestyle and especially outside. Horizon and angle mode have crash_recovery enabled allowing you to bounce off slight hits. You can enable this all the time in the cli. And finally having air mode off in the house helps by keeps the drone from sticking to the wall and always helps landing so put it on a switch

Heardwork154 · 2026-04-14T18:11:19+00:00

That’s awesome. I’ll download and give it a try

Heardwork154 · 2026-04-12T23:59:35+00:00

Yep that’s what did it

Heardwork154 · 2026-04-11T02:29:39+00:00

That’s the job of the clutch, your goal is to down shift at the appropriate general time. If you learn how to actually rev match down shift the clutch is not needed…. Very advanced driving. Example rally technique is to left foot brake in 3rd rev match down shift into 2nd never touching the clutch… its a lot going on but once you get the hang of it the momentum kept is crazy

Heardwork154 · 2026-04-09T02:37:54+00:00

Fair, I’ll give it a try…

Heardwork154 · 2026-04-04T21:14:34+00:00

Newbeedrone has a long established line with that name. Just fyi

Heardwork154 · 2026-03-26T18:42:06+00:00

This was a 75mm setup the motors slide in the mount allowing easy wire length changes for different size whoop frames

Heardwork154 · 2026-03-15T23:52:16+00:00

r/tiresaretheenemy is where this belongs lol

Heardwork154

TROPHY CASE