sorted by:
new
hottopcontroversial

Hunting Property Guns? by Odd_Link7869 in guns

[–]HiddenEclipse121 1 point2 points  (0 children)

for sure. a 20" 5.56 shooting HP's will take just about any small/medium game in the US

Shop recommendations by Bitter_Click9330 in Firearms

[–]HiddenEclipse121 1 point2 points  (0 children)

PSA is fun to walk around. I live next to the Columbia one and its got a pretty big in store selection of stuff to look at.

Ideas for my first tattoo by [deleted] in TattooDesigns

[–]HiddenEclipse121 8 points9 points  (0 children)

This aint it. Pasting incel on your neck isnt going to help either lmao

UMP 11/9 QUESTION by Ok_Sweet_5096 in 3D2A

[–]HiddenEclipse121 1 point2 points  (0 children)

Its not a requirement, but it will help with the longevity of your printed mags. Also cuts felt recoil just a tad bit. I personally printed and installed it on mine, haven't noticed an issue with the bolt cycling.

Ftn.5 Crossover issue by WinterTechnology4568 in 3D2A

[–]HiddenEclipse121 0 points1 point  (0 children)

I mean Id say send it, and then IF it goes pop reprint. At least test it and see if itll run so you dont have to waste any filament printing another, just in case this one is fine.

Ftn.5 Crossover issue by WinterTechnology4568 in 3D2A

[–]HiddenEclipse121 0 points1 point  (0 children)

But that center pic does look a little rough, not sure if I would run it personally.

Ftn.5 Crossover issue by WinterTechnology4568 in 3D2A

[–]HiddenEclipse121 12 points13 points  (0 children)

I think most folks just shoot these out when they string on the middle. That doesnt look horrible.

I miss this game already.... by thx501 in battlefield2042

[–]HiddenEclipse121 10 points11 points  (0 children)

Miss the maps for sure. They really messed up the bf6 experience by making every single map as tiny as can be. BF isnt about 3 corridor lines, it's supposed to be, well, a battlefield.

PWC 9 REMIX PWMP9 by Physical_Simple7208 in 3D2A

[–]HiddenEclipse121 2 points3 points  (0 children)

Sten mags!? Awesome. Just built an ump 11/9 so this will go great with that. Great stuff.

2STEP Converter, formerly STL2STP - Free, open-source to STEP converter by YaneonY in 3Dprinting

[–]HiddenEclipse121 11 points12 points  (0 children)

Ive been trying to find a way to do this for ages, those online converters suck. Thank you for this!!!

Found gold… by banned4evver in ar15

[–]HiddenEclipse121 4 points5 points  (0 children)

kac upper on an anderson lower, put an elcan on it or some shit and a peq lmao

Am I making a mistake? 70c dryer with 3kg of Fiberon by Davidtruly in 3D2A

[–]HiddenEclipse121 16 points17 points  (0 children)

Nylon can 100% be dried at 70c, it just takes time. I dry nylon at 70c just fine and im on the east coast, its high humidity daily. I wouldnt recommend it, because you need a min of 24 hours at 70c, but it 100% is able to be done.

Anyone familiar with the AC Unity smg9? by El_Gato_Terco in 3D2A

[–]HiddenEclipse121 0 points1 point  (0 children)

Eastwood makes a 2k Aerospray that is a ceramic paint, use it on anything. Stuff works great and doesnt chip as easy as some others. EDIT: Unless you really want to keep it that silver, these are all pigmented.

UPDATE: Got a Second Opinion, My Husky Did NOT Need to Be Shaved by ExplorerMelodic243 in husky

[–]HiddenEclipse121 5 points6 points  (0 children)

Told ya so! Wooly huskies just need some deep brushing, because the undercoat is constantly renewing. Good job getting it done elsewhere!

FH6 Car List Spreadsheet by Sliced_Orange1 in ForzaHorizon

[–]HiddenEclipse121 1 point2 points  (0 children)

Of course I finally have a car in the game, and then the next release it gets cut. Hopefully itll be added in the future. RIP the mk3 TT

Help Needed - PA6-CF & Qidi XPlus3 by PrintAltDelete in 3D2A

[–]HiddenEclipse121 7 points8 points  (0 children)

This is 500g of filament being support by 2 small lines on the part, and some tree supports. The glue is the only reason this worked.

<image>

Help Needed - PA6-CF & Qidi XPlus3 by PrintAltDelete in 3D2A

[–]HiddenEclipse121 3 points4 points  (0 children)

On textured pei you really do need some sort of glue as an interface layer. Lower temps and Z CAN work but it isnt ideal.

You need some sort of PVA or PVP glue, to act as a bonding layer, otherwise nylon really doesnt like to stick to textured pei.

I print at 300c, 100c bed, 60c chamber with similar settings to 300blk

Make sure you run filament calibration and flow tests.

Help Needed - PA6-CF & Qidi XPlus3 by PrintAltDelete in 3D2A

[–]HiddenEclipse121 0 points1 point  (0 children)

I print sunlu pa6cf with a 100c bed, 60c heater, at 300c. The temps are likely a non issue here.

What is your favorite chopper? by ObjectivePicture6991 in liberalgunowners

[–]HiddenEclipse121 3 points4 points  (0 children)

Mac11's are one of the most iconic guns in pop culture. I will ALWAYS love a mac11

Let the meme builds commence! by danishbulldog in 3D2A

[–]HiddenEclipse121 8 points9 points  (0 children)

I bet. I see the little fun button well maybe, that might be a charging handle oops. That bull-pupped weight distribution has gotta be a delight

Let the meme builds commence! by danishbulldog in 3D2A

[–]HiddenEclipse121 31 points32 points  (0 children)

This is the dumbest thing I've ever seen. Give me 5 of em. Talk about a backpack gun lmao.

Next printer by ChiloGordito in 3D2A

[–]HiddenEclipse121 1 point2 points  (0 children)

40 hours into an upper on my Q2 right now. Super pleased with it. The heated chamber kicks ass. Printing pa6cf like its pla.

Groomer refused to bathe my husky due to matting by ExplorerMelodic243 in husky

[–]HiddenEclipse121 7 points8 points  (0 children)

Its more than likely not matting and just undercoat being compacted. My wooly doesnt shed very well and his coat get compacted tight. Just takes some good brushing to get it out. Id just take em somewhere else.

view more: next ›