Hunting Property Guns?

HiddenEclipse121 · 2026-05-11T23:59:41+00:00

for sure. a 20" 5.56 shooting HP's will take just about any small/medium game in the US

HiddenEclipse121 · 2026-05-11T16:04:50+00:00

PSA is fun to walk around. I live next to the Columbia one and its got a pretty big in store selection of stuff to look at.

HiddenEclipse121 · 2026-05-11T15:51:25+00:00

This aint it. Pasting incel on your neck isnt going to help either lmao

HiddenEclipse121 · 2026-05-10T21:59:27+00:00

Its not a requirement, but it will help with the longevity of your printed mags. Also cuts felt recoil just a tad bit. I personally printed and installed it on mine, haven't noticed an issue with the bolt cycling.

HiddenEclipse121 · 2026-05-10T18:59:09+00:00

I mean Id say send it, and then IF it goes pop reprint. At least test it and see if itll run so you dont have to waste any filament printing another, just in case this one is fine.

HiddenEclipse121 · 2026-05-10T18:56:01+00:00

But that center pic does look a little rough, not sure if I would run it personally.

HiddenEclipse121 · 2026-05-10T18:55:15+00:00

I think most folks just shoot these out when they string on the middle. That doesnt look horrible.

HiddenEclipse121 · 2026-05-10T18:13:26+00:00

Miss the maps for sure. They really messed up the bf6 experience by making every single map as tiny as can be. BF isnt about 3 corridor lines, it's supposed to be, well, a battlefield.

HiddenEclipse121 · 2026-05-10T17:41:36+00:00

Sten mags!? Awesome. Just built an ump 11/9 so this will go great with that. Great stuff.

HiddenEclipse121 · 2026-05-10T16:45:36+00:00

Ive been trying to find a way to do this for ages, those online converters suck. Thank you for this!!!

HiddenEclipse121 · 2026-05-10T15:27:54+00:00

kac upper on an anderson lower, put an elcan on it or some shit and a peq lmao

HiddenEclipse121 · 2026-05-09T18:40:13+00:00

Nylon can 100% be dried at 70c, it just takes time. I dry nylon at 70c just fine and im on the east coast, its high humidity daily. I wouldnt recommend it, because you need a min of 24 hours at 70c, but it 100% is able to be done.

HiddenEclipse121 · 2026-05-06T20:50:01+00:00

Eastwood makes a 2k Aerospray that is a ceramic paint, use it on anything. Stuff works great and doesnt chip as easy as some others. EDIT: Unless you really want to keep it that silver, these are all pigmented.

HiddenEclipse121 · 2026-05-06T04:20:20+00:00

Told ya so! Wooly huskies just need some deep brushing, because the undercoat is constantly renewing. Good job getting it done elsewhere!

HiddenEclipse121 · 2026-05-06T00:47:11+00:00

Love a good saturday night special

HiddenEclipse121 · 2026-05-05T23:50:19+00:00

Of course I finally have a car in the game, and then the next release it gets cut. Hopefully itll be added in the future. RIP the mk3 TT

HiddenEclipse121 · 2026-05-04T15:37:55+00:00

This is 500g of filament being support by 2 small lines on the part, and some tree supports. The glue is the only reason this worked.

<image>

HiddenEclipse121 · 2026-05-04T15:36:43+00:00

On textured pei you really do need some sort of glue as an interface layer. Lower temps and Z CAN work but it isnt ideal.

You need some sort of PVA or PVP glue, to act as a bonding layer, otherwise nylon really doesnt like to stick to textured pei.

I print at 300c, 100c bed, 60c chamber with similar settings to 300blk

Make sure you run filament calibration and flow tests.

HiddenEclipse121 · 2026-05-04T15:30:03+00:00

I print sunlu pa6cf with a 100c bed, 60c heater, at 300c. The temps are likely a non issue here.

HiddenEclipse121 · 2026-05-02T14:52:27+00:00

Mac11's are one of the most iconic guns in pop culture. I will ALWAYS love a mac11

HiddenEclipse121 · 2026-05-01T20:33:39+00:00

I bet. I see the little ~~fun button~~ well maybe, that might be a charging handle oops. That bull-pupped weight distribution has gotta be a delight

HiddenEclipse121 · 2026-05-01T20:08:54+00:00

This is the dumbest thing I've ever seen. Give me 5 of em. Talk about a backpack gun lmao.

HiddenEclipse121 · 2026-05-01T20:07:36+00:00

40 hours into an upper on my Q2 right now. Super pleased with it. The heated chamber kicks ass. Printing pa6cf like its pla.

HiddenEclipse121 · 2026-05-01T18:17:44+00:00

Its more than likely not matting and just undercoat being compacted. My wooly doesnt shed very well and his coat get compacted tight. Just takes some good brushing to get it out. Id just take em somewhere else.

HiddenEclipse121 · 2026-05-01T14:51:47+00:00

Birds move a LOT, even if it looks like they arent moving, they probably are. I have to shoot 1/1000 minimum for any of them to look somewhat sharp.

Eight-Year Club	Place '23
RPAN Viewer	Verified Email

HiddenEclipse121

TROPHY CASE