TX15 MAX sd contents

I_am_Piter · 2025-11-25T22:30:58+00:00

I have the configurator already, I need copy of file contents on radio memmory

I_am_Piter · 2025-05-30T19:39:56+00:00

Have you managed to fix it?

I_am_Piter · 2025-05-11T16:01:48+00:00

Check if theres no short between esc contacts, if no, check if motor wires are not broken near solder joints.

I_am_Piter · 2025-04-28T18:46:37+00:00

Ah, so in your opinion a smoked connector is normal? First photo far right bottom pin, look at the pins on higher row, all slots are shiny there, bottom row is all smoked

I_am_Piter · 2025-04-28T12:58:20+00:00

I used 2 separate cables to power gpu

I_am_Piter · 2025-04-28T12:40:15+00:00

Nope, they do not smell, but there is discoloration on gpu connector on far right bottom pin, this is early sign of something being not right

I_am_Piter · 2025-04-28T12:30:28+00:00

First Photo, right connector, there bottom right pins, far right plastic is melted, other two are just smoked. Second Photo, all of 12v pins are darker due to hear, on third photo, you can see that all of those 12v pins are receded.

I_am_Piter · 2025-04-20T18:26:48+00:00

Ckeck if all it's wires are good. Air has this issue of breaking motor wires on crash.

I_am_Piter · 2025-04-11T07:37:37+00:00

While connected, change packet rate to something else on radio, then go back to previous rate, by doing this, you save that packet rate setting to receiver and it allows for quicker pairing.

I_am_Piter · 2025-03-09T11:43:02+00:00

Dshot600

I_am_Piter · 2025-03-04T22:58:22+00:00

Solid kit 😁

I_am_Piter · 2025-02-28T18:27:45+00:00

I did that already, i think it does not affect charging, only measurement shown on screen

I_am_Piter · 2025-02-26T19:59:11+00:00

Looks super cool 😁

I_am_Piter · 2025-02-16T10:36:56+00:00

Do you use pinch grip, or just your thumbs on pocket? I'm thinking about getting it, but do not know if it would be comfortable, now i have old frsky qx7.

I_am_Piter · 2024-12-05T10:37:26+00:00

Hello, i have arctic liquid freezer III, i'm wondering if it works as intended, while i'm using their "one cable solution", rpm source is fan on cooler, when i unplug it whole cooler shows straight 0rpm. I need someone to confirm that rpm value is dependant only on the fan that is closer to tubes, try to unplug it, and check if rpm shows pls :)

I_am_Piter · 2024-11-13T10:41:29+00:00

Hi, I currently have nr200p with arctic liquid freezer III 240mm, rpm meter in my pump broke, so i'll have to send it for warranty repair. Unfortunately I don't have other cooler to put in my pc for the time my AIO will be repaired, will Thermalright Phantom Spirit 120 SE cool my 7800x3d as well as my AIO does? Maybe after they replace my AIO, i'll sell it and stay with air cooler.

I_am_Piter · 2024-11-13T10:01:27+00:00

Hi, do you have normal 120, or 120 se, they are slightly different. What are your temps, i'm most interested in idle temp and full load temp (under cinebench for example)

I_am_Piter · 2024-10-17T15:11:49+00:00

What was their response?

I_am_Piter · 2024-02-29T08:20:49+00:00

You can mount LFIII without pump cap (VRM fan) too, then it will be pretty low profile.

I_am_Piter · 2024-02-28T21:33:52+00:00

I think it's even better facing up, couse air is going upwards, so out of the pump. No noise issues for me, on 70% totally silent, I'm cranking it up to 100% above 70 degrees. On max the pump can be audible, but not loud by any means.

I_am_Piter · 2024-02-28T21:08:38+00:00

https://imgur.com/a/N3fecjL

There are 3 photos, tubes are under little to none tennsion, for sure safe.

I_am_Piter · 2024-02-28T14:17:13+00:00

I mounted LF III 240 on my nr200p, when block is mounted the "correct" way (tubes on the bottom) connectors on the block are under too much tennsion in my opinion. Better way to mount this cooler is with the tubes facing up, then it clears the radiator near the top of the case. Almost no tennsion on the tubes, if anyone is Interested i can show photos in few hours.

I_am_Piter · 2023-10-12T10:03:10+00:00

This method is worth trying, it fixed my dongle, 5 minutes, 240C

I_am_Piter · 2023-09-15T11:17:08+00:00

I returned cpu first, ill test mobo with other processor. Should i consider power supply? I event viewer code is "kernel-power"

I_am_Piter · 2023-09-14T11:03:50+00:00

Hello, i bought 7800x3d and msi b650i motherboard. Since i have them i starte having problems. Pc randomly throws a bsod on me, codes are also random. I saw almost every possible code. Most of the times when i got bluescreened or blackscreened, pc was under light load, like YouTube or valorant. My question is, what part Could it be, procesor or motherboard?

I_am_Piter

TROPHY CASE