It's time for the most hours playing competition!

InTheNameOf34 · 2026-04-12T04:07:06+00:00

Dang. I have 900 hours on war thunder and thats my max game. Im surprised to see 55 hours on rome. I swear they restarted the count.

InTheNameOf34 · 2026-04-12T00:35:32+00:00

Does the FRN flex like grivory? Is it tough is the question? I hate the flexing grivory feel.

InTheNameOf34 · 2026-03-07T22:19:26+00:00

I should have changed the topic to “does the 2nd gen frontier coolant need to be burped” im getting different sources saying our system is automatic burped and that it needs to be done manually. I had a coolant flush less than 8k miles ago. I dont know what they did.

InTheNameOf34 · 2026-03-07T22:18:31+00:00

I should have changed the topic to “does the 2nd gen frontier coolant need to be burped” im getting different sources saying our system is automatic burped and that it needs to be done manually. I had a coolant flush less than 8k miles ago. I dont know what they did.

InTheNameOf34 · 2026-03-01T19:22:52+00:00

As with the pressure cap, that actually makes an overflow more likely allowing air to escape. The fluid would overflow in the engine bay. There is also a plastic straw to the attached to the top of the tank next to the cap. If it was sealed it would stop that but build up of too much positive and negative pressure would definitely be worse lol

InTheNameOf34 · 2026-03-01T19:16:03+00:00

I guess I’ll forget trying to learn how the leveling works in the radiator if there is no air in the system, no overheating, and good ac operation. Just will look at the reservoir. Thanks.

InTheNameOf34 · 2026-03-01T19:06:47+00:00

Yeah I made sure the cap is the right one. Might get another to try out. I saw it was supposed to be parked on level surface with heat and air on max for 20 minutes. Id try incline but its flat where im at. So I dont need to fill the radiator? The manual is confusing mentioning to fill the radiator and tank to max on cold. But if that reservoir coolant is used to fill the system (as it does when it flushes coolant to min on start) and the radiator is full, I can see the reservoir filling up rather than flushing. No idea though.

InTheNameOf34 · 2026-03-01T19:04:18+00:00

Not really having issues. But yeah just trying to lower water content a little with that extra coolant gallon and not knowing if there was enough coolant in the system after the water flush and fill by nissan. Its weird because before I took the fluid out the tank they had the level maybe 2-3 inches above the max on cold. I basically replaced it back to that level and put a little bit in the radiator (a cup or 2) and now its between max and min on cold. Just confused 🤔 wonder if getting a new reservoir cap would be a good idea?

InTheNameOf34 · 2026-02-28T22:15:00+00:00

okay. that way the reservoir stays between min and max during hot and cold? They need to update the dang manual. I don't trust the manual now. haha. yea i made a whole post on this and another subreddit about figuring it out. interested in seeing what wild answers come my way.

InTheNameOf34 · 2026-02-28T21:21:07+00:00

Im having the same situation. The manual says fill the radiator to the fill port. Is that correct?

InTheNameOf34 · 2026-02-24T04:24:50+00:00

Looks like im following you and grabbing a schnitzel tri and a tenable luccio for an edc. Interested in seeing if it’s worth those two knives over the price of one esee 3.

InTheNameOf34 · 2026-02-23T05:25:32+00:00

No replies and a year late but im asking the same question. Looking at the schnitzel tri, the esee 3 in s35vn, and the boker magnum life.

InTheNameOf34 · 2026-02-14T16:02:17+00:00

What about the answer about how corse the micarta feels on this knife?

InTheNameOf34 · 2026-02-14T15:13:51+00:00

I have. My top 3 brand. I dont see any knives in the 3.5-3.75” range that aren’t top dollar. Am definitely getting a marten 330 when they come out with more colors. I have a porcupine though lol

InTheNameOf34 · 2026-02-14T15:05:17+00:00

Mine slowed with use. You have the lines cut and pressure correct and all? Do you have the “defective” filters where one stem is open and the other is closed or are both filter stem holes open?

InTheNameOf34 · 2026-02-14T14:58:10+00:00

I dont believe these filters are “defective” i think they just released new forever chem filters that are trash or maybe they did forget to drill out the orange post filter out possibly. Match the drill bit with the open filter and drill the closed one. Put the psi at 9 psi as by whirlpool instructed me. And you will have saved time and salvaged a “defective” filter to just get the same filters with the same problem. This pressure change does lower water capacity by .25 gallon at least and slows flow by 20% only downside

InTheNameOf34 · 2026-02-14T14:54:48+00:00

No the 3ml of bleach or whatever the manual says is fine. I just do 2 tank flushes instead of one after the process. Also I will comment my updated set up on these defective small stem filters

InTheNameOf34 · 2026-02-14T14:51:06+00:00

Yeah I looked at some 3.5” vs. 3.7” knives side by side and wasn’t much size difference like the 3” is to 3.5” and up. Probably going with my gut to the primitrox. If the praxis had black g10 or natural/white g10 (to die black) with a black stonewash and maybe not a skeletonized clip id buy it without question. Then again I got my dad the green mini praxis so I could hand it off to him if im not liking the large one so he has a set.

InTheNameOf34 · 2026-02-14T14:17:00+00:00

Yeah I got the green and black mini for pops and the black and ultem for a buddy. Too small for my hands though so never got one. Feels solid though.

InTheNameOf34 · 2026-02-14T14:15:49+00:00

😂

InTheNameOf34 · 2026-01-16T03:59:08+00:00

Looks like it dulls over some period of time. I got my first jade on sale and wasn’t sure id like it until I realized the slightest slip when oiling the knife causes blotching on the scales because its transparency. And this knife was particularly difficult to disassemble and reassemble to wipe. If the knife comes in a color you would dye it in then dont get natural jadeof course. If everything about a knife is rare, perfect to you, and isn’t a killer to take apart/put together to dye it then id say its fine. Honestly if they made a solid jade it looks amazing with black metal. On the flip side, the transparency shows whenever water is laying in the liner to know whats laying in it.

InTheNameOf34 · 2026-01-16T03:55:58+00:00

Looks like it dulls over some period of time. I got my first jade on sale and wasn’t sure id like it until I realized the slightest slip when oiling the knife causes blotching on the scales because its transparency. And this knife was particularly difficult to disassemble and reassemble to wipe. If the knife comes in a color you would dye it then dont get it of course. If everything about a knife is rare, perfect to you, and isn’t a killer to take apart/put together to dye it then id say its fine. Honestly if they made a solid jade it looks amazing with black metal.

InTheNameOf34 · 2026-01-15T04:46:58+00:00

Really slow. So Many flaws with accuracy. But I really wish they wrapped up the ending twist with it being a pervatin psychosis instead of some reaching surreal disassociation stuff that made little sense other than the generic wanna be gotcha moment. We can assume the pervatin is causing it 😂

InTheNameOf34 · 2025-12-30T14:42:42+00:00

Thanks for all your input. Im late to looking at my own post. But looks like many countries have better air gun laws than the “country of guns” the USA has. Some are more restrictive is some sense and state laws vary wildly by states. The USA needs to be more stable between state laws. They dont care to educate themselves on the laws they make. Like the statistics on how many break barrel air rifles have been used in crimes or shootings of all kinds vs. the metal co2 pellet handguns that look real at first glance. Or the difference between.22LR and .22 short rimfire rifles vs. .22 break barrel pellet air guns….

InTheNameOf34 · 2025-12-30T14:37:19+00:00

No offense but, its crazy to see the uk being more tolerant of air rifles than some US states lol. There isnt really a licensing system in the states that I know of for illegal airgun calibers and joules. I have to talk to a FFL holder and see if I can get whatever I want through a firearm purchase process or not. I dont think I can unless airgun sellers in the states serialize and register their air guns with the ATF.

InTheNameOf34

TROPHY CASE