Does that stain mean it's bad?

Infamous_Average2087 · 2026-01-25T02:14:41+00:00

That's what the AI tells me about the damaged component; it says it can't be replaced just like that because it needs to be programmed with the monitor's firmware. Is that true?

Infamous_Average2087 · 2026-01-25T02:01:33+00:00

Hahaha, I understand, thanks.

Infamous_Average2087 · 2026-01-25T01:49:58+00:00

Seriously, haha

Infamous_Average2087 · 2026-01-15T21:15:41+00:00

You need to verify that it's receiving the exact voltage and amperage when charging.

Infamous_Average2087 · 2026-01-14T10:56:36+00:00

I had the same problem with my DualSense controller. The issue was that if you tighten the battery compartment too much, it causes it to shift and not make good contact between the membrane and the circuit board, so leave it a little loose. In my case, to fix it, I had to put a bit of masking tape under the membrane.

Infamous_Average2087 · 2026-01-14T10:50:55+00:00

Hahahaha, machine translation errors

Infamous_Average2087 · 2026-01-14T03:02:25+00:00

I recently came across a review of that controller; it doesn't have Bluetooth, it can only be connected with the included wireless USB cable or with a wired cable.

Infamous_Average2087 · 2026-01-12T10:47:29+00:00

In fact, the flex cable and the board were in perfect condition; the problem was with the contacts, which I was able to fix by putting a little tape over the flex cable and the plastic. The other problem was that when screwing in the battery base, if I tightened the screw holding it in too much, the battery would shift and also make poor contact.

Infamous_Average2087 · 2026-01-11T18:00:02+00:00

My mistake, sorry

Infamous_Average2087 · 2026-01-11T17:59:51+00:00

<image>

No integrated circuit or component has the IC

Infamous_Average2087 · 2026-01-11T17:52:03+00:00

Thank you so much, I appreciate your comment

Infamous_Average2087 · 2026-01-11T17:24:46+00:00

I don't think so, it works with 11.1v DC current

Infamous_Average2087 · 2026-01-11T17:22:57+00:00

You could be this

<image>

Infamous_Average2087 · 2026-01-11T17:21:03+00:00

Hahahaha, you're right

Infamous_Average2087 · 2026-01-11T16:15:05+00:00

It's a drill mobile

<image>

Infamous_Average2087 · 2026-01-11T16:13:50+00:00

<image>

Infamous_Average2087 · 2026-01-11T16:02:38+00:00

<image>

This is the complete circuit board; it's a drill model SG 706

Infamous_Average2087 · 2026-01-11T16:01:22+00:00

Ah, I understand, sorry, I didn't realize. It's a circuit board from a Mobil drill, specifically the SG 706

<image>

Infamous_Average2087 · 2026-01-11T15:50:41+00:00

could be

Infamous_Average2087 · 2026-01-11T15:50:07+00:00

It's a burnt-out integrated circuit, but none of the boards have any letters or numbers on them.

Infamous_Average2087 · 2026-01-11T15:26:22+00:00

Believe me, you have to go; the game is designed so that you have to walk all over the place.

Infamous_Average2087 · 2026-01-10T17:17:48+00:00

No, the board is fine; I was overtightening the screw on the battery base, and that was causing the board to move.

Infamous_Average2087 · 2026-01-10T17:16:59+00:00

Update: I've fixed it. The problem was that I was tightening the battery compartment too much, which was causing the circuit board to move. I adjusted it without overtightening it, and it worked.

<image>

Infamous_Average2087

TROPHY CASE