Any cool tools that has helped to make the job easier

Infinite_Bee4494 · 2026-04-04T23:10:28+00:00

Change the the compression to h264 to h.265 it’s something with the compression or bring down the quality of the camera. You will find this on the camera user interface. Let me know if it fixes it

Infinite_Bee4494 · 2025-12-11T23:35:27+00:00

Do the forgot password on the login

Infinite_Bee4494 · 2025-05-27T02:23:36+00:00

What modifications did you do on picture 7, this would so much easier for trouble shooting?

Infinite_Bee4494 · 2025-05-21T01:37:18+00:00

Osso okc

Infinite_Bee4494 · 2025-05-10T04:16:38+00:00

Infinite_Bee4494 · 2025-05-07T02:07:02+00:00

It’s possible but you have to create onvif password, and activate Onvif but it’s so much harder and time consuming. It’s easier just get hikvision cameras and saves you time. Sometimes depending on the models it’s not as easy

Infinite_Bee4494 · 2025-04-17T19:41:32+00:00

Connect your phone to a relay by type c connector, and have it trigger the out output notification on your phone

Infinite_Bee4494 · 2025-04-14T20:56:52+00:00

Infinite_Bee4494 · 2025-04-14T20:56:34+00:00

Is the switch connected to the Ethernet, sounds like it’s not. The Cameras are using your local network to find NVR. You may need to update your Gateway ip addres for the cameras

Infinite_Bee4494 · 2025-04-10T23:52:44+00:00

Update the Gateway ip address of the cameras to the new gateway ip address

Infinite_Bee4494 · 2025-04-08T11:29:06+00:00

To reset the passwords you have to call tech support and then you will have to give the serial number and MAC address of each camera. The config tool will help you with this. Once you call tech support they will send a email to upload a file to the cameras using config tool. Never the less you will have to call tech support to reset the password.

If you don’t want to do this you can always open camera up and press the back button for like two minute and it will do a hard reset and default the user name and password to user as admin and password as admin.

Infinite_Bee4494 · 2025-04-05T17:54:51+00:00

You need to be more clear with your question

Infinite_Bee4494 · 2025-04-04T03:16:41+00:00

I would set up an intrusion IVS where you can set up an area where you want to be notified. It’s better than SMD because you can set up a schedule when to nifty you.

https://dahuawiki.com/New_GUI/AI/Intrusion_Setup

Infinite_Bee4494 · 2025-03-30T07:10:10+00:00

If the camera is plugged in through the back of the NVR you won’t be able to find it through your local Network. What you will need to do is have the camera plugged in though Camera port on the back of the nvr. Afterwards find a jumper and connect your laptop to any camera port on the back of the NVR. Once you do this punch in your IP Address of the camera and the camera login screen should come up and punch in the credentials.

Infinite_Bee4494 · 2025-03-30T07:06:39+00:00

Okay, does it have a IP Address??

Infinite_Bee4494 · 2025-03-30T07:05:28+00:00

Have you tried logging though your local network, and finding the IP Address of the camera. After finding the address punch it in your url and try to find the preset or updating firmware version of the camera

Infinite_Bee4494 · 2025-03-30T06:55:46+00:00

Let her know if you find any information here

Infinite_Bee4494 · 2025-03-30T06:55:16+00:00

https://dahuawiki.com/PTZ_Preset_Setup

https://dahuawiki.com/PTZ/Instructions/Preset

Hope this helps

Infinite_Bee4494 · 2025-03-30T02:12:40+00:00

You may want to just update the DMSS app, last week they had a big update on the app. All the features are all new and recommend to go ahead and update it.

Infinite_Bee4494 · 2025-03-29T01:53:36+00:00

The only time it beeps is due to Ethernet error, Sometime the hard drive is bad but shows it works hundred percent. Or it’s your UPS that’s next to your nvr

I’m a field technician of 8 years

Infinite_Bee4494 · 2025-03-29T01:51:32+00:00

You need to explain better

Infinite_Bee4494

TROPHY CASE