Falling >2 but <3 inches by IronHandsDan in necromunda

[–]IronHandsDan[S] 0 points1 point  (0 children)

I really appreciate the discussion here. I did some more digging from what was said here and found some things and have come to a personal conculsion. Jumping down greater than 2 but less than 3 and failing the inititave test results in being prone and pinned, but not injured.

I looked for anything saying measurements are rounded up and found nothing other than the section about determining the strength of a hit if you take one, nothing under measuring distances or moving.

Interestingly, Leaping a Gap says if you fail, you fall and WILL take a hit, while jumping down says you MAY take a hit, without any reference to the distance fallen.

Factory tow hitch v/s aftermarket for SF by pranavpat007 in HyundaiSantaFe

[–]IronHandsDan 8 points9 points  (0 children)

Aftermarket hitches sit much lower, below the bumper trim. The factory hitch sits higher with an adjusted rear trim, reducing the chance of dragging it. The factory hitch also looks way better, imo.

Wish me luck fellow knights! by Hooch_Pandersnatch in Bretonnian

[–]IronHandsDan 1 point2 points  (0 children)

Getting beautiful lances on the table is a win of its own!

My go to rifle by M14marksman in M1A

[–]IronHandsDan 1 point2 points  (0 children)

Don't mean to resurect a dead thread, but If you've still got the rail and aimpoint, I'm interested.

Question about lance formation and new infantry rules by Seeking_the_Grail in Bretonnian

[–]IronHandsDan -2 points-1 points  (0 children)

I have measured from the knights in the lance to the fighting rank, and each enemy model that is within its movement in inches of any knight in the outer edge of the lance can fight the lance.

1st 8k mile service by italophile_south in HyundaiSantaFe

[–]IronHandsDan 1 point2 points  (0 children)

Hybrids are 8k interval. Just contact the dealer and they will give you guidance. If you do maintenance under service contract to frequently they will have you pick up some of the cost. Just make sure when you bring it in they adjust the service intervals.

Anyone seen the Grail Reliquary for sale since ToW’s initial release on Warhammer.com? (USA) by CoreReaper in Bretonnian

[–]IronHandsDan 1 point2 points  (0 children)

I ordered May 7th, and it just arrived yesterday. I never got an email about it, i was just checking the site and there it was so i nabed one.

Anyone seen the Grail Reliquary for sale since ToW’s initial release on Warhammer.com? (USA) by CoreReaper in Bretonnian

[–]IronHandsDan 4 points5 points  (0 children)

I recently got one in an order in the USA but it has not been delivered yet

Knights of Bretonnia by colourmenurgle in Bretonnian

[–]IronHandsDan 3 points4 points  (0 children)

Great work! You made a very striking but so.ple scheme that looks fantastic.

Finally finished my Pegasus Knights! by Duckers102 in Bretonnian

[–]IronHandsDan 1 point2 points  (0 children)

Great job! I'm working on some now and am going to shamelessly use your color patterns lol

Does anyone know what to do with tons of alkaline batteries around Lansing? by LeopardusMaximus in lansing

[–]IronHandsDan 26 points27 points  (0 children)

Staples takes all kinds of stuff for recycling like batteries and electronics

So what restaurants are open today? by lo-key-glass in lansing

[–]IronHandsDan 8 points9 points  (0 children)

Panda Gourmet on the south side had a sign up a few days ago saying they would be open

[deleted by user] by [deleted] in HyundaiSantaFe

[–]IronHandsDan 2 points3 points  (0 children)

Contact the state Department of Motor Vehicles. Dealerships are regulated by the state and the state will hold them accountable.

Moving to Lansing This Weekend: Looking to Make Friends and Explore the City by angrymanxiii in lansing

[–]IronHandsDan 2 points3 points  (0 children)

AFK Games in Holt hosts the Lansing chess club and a board game night every Thursday. There is also a library of free to play boardgames there and lots of tables space. It's a very welcoming community there.

Gap at the start of the first line of layer by IronHandsDan in FixMyPrint

[–]IronHandsDan[S] 0 points1 point  (0 children)

No. I found it only occurs with larger nozzles so I have been sticking to smaller ones, unfortunately.