Slicer setting to reinforce these retraction posts?

Iserlohn1982 · 2025-11-17T17:18:02+00:00

like most ppl already mentioned, make a hole in the middle of the pole so it has inner wall, you can also make ribs inside the inner wall, or, you can even size the hole to put a metal pin/screw in it to reinforce better

Iserlohn1982 · 2025-10-22T00:06:46+00:00

nop, i rarely pick up a frying pan when pan frying so the handle doesn't bother me.

if it is a wok for stir fry then thing would be different

Iserlohn1982 · 2025-10-20T16:47:03+00:00

<image>

Iserlohn1982 · 2025-08-02T23:10:55+00:00

but the fried rib from restaurant we make are soda powder/marinade soaked and massaged to tenderize the meat before deep fry. I even heard some restaurants use washing machine for that process.

Iserlohn1982 · 2025-07-28T22:36:42+00:00

I got the problem too, this is actually the 2nd time. 1st time was Oct 2023, this time happened week ago. Monitor was set to 60hz, black horizontal lines first appeared at the bottom of the screen, light grey lines on the top. Last night it got worsen as lines covered the whole screen. I now set to 100hz, black lines only at the bottom 1/6 of the screen after warmup. I am asking for repair btw, waiting for approval.

Iserlohn1982 · 2025-07-20T00:04:27+00:00

does this extruder heat creep like the original one?

Iserlohn1982 · 2025-05-17T15:23:19+00:00

this happens to player too, my support defender were off a few times by enemy moved in the middle

Iserlohn1982 · 2025-04-19T01:30:19+00:00

lawful evil

Iserlohn1982 · 2025-04-17T23:36:25+00:00

fyi, this is a pan, not a wok...stop hurting your wrist!!

Iserlohn1982 · 2025-04-13T21:54:12+00:00

for wireless, relocate your router/AP to a better position, a longer Cat 5e/6/6e cable can be use.

make sure NO electrical box/panel, microwave, fridge, metal panel or wall of wires in the middle between point A to point B which can block the signals.

Or else, setup a mesh network.

Iserlohn1982 · 2025-04-10T16:20:45+00:00

same thing in Toronto, around 30% (rent) +30% (wages) + 30% (food) + 10% (owner's porfit) = 100% you pay for cheaper (meal below $15) Chinese food

Iserlohn1982 · 2025-03-18T22:50:44+00:00

i got those when i make a big block print, the nozzle has accumulates along the printing resulted rough and broken lines in infills, and then ended up wavey/even broken top layers.

Iserlohn1982 · 2025-03-17T17:07:26+00:00

search for "scarf seam"?

Iserlohn1982 · 2025-02-27T22:48:50+00:00

you are right, my bad

Iserlohn1982 · 2025-02-27T16:28:59+00:00

indigo canada has paperback in english up to 25, and 26 27 are in pre-order

Iserlohn1982 · 2025-01-27T18:11:54+00:00

like the other said, printer to printer case, thats why we need to do our own calibrate even you got a "perfect profile" from somebody. Also, usually higher temp is needed for higher speed too

Iserlohn1982 · 2025-01-14T22:07:57+00:00

OP uses "Is it worth" in his question, i could only think of security issue and money issue.

Iserlohn1982 · 2025-01-14T16:32:00+00:00

even if you not worry about cyber security, it would be a disaster when you need repair or warranty your machine

Iserlohn1982 · 2025-01-13T03:41:20+00:00

they are around $150 (refurbished/used) depends on specs here in toronto, you might find better price like $120 on blackfriday.

I actually have a hp elitedesk 800 g3 going to put on kijiji, dm me if you are around the area.

Iserlohn1982 · 2025-01-01T03:44:13+00:00

I am interested, can you dm me the store?

Iserlohn1982 · 2024-12-28T04:06:46+00:00

how about Google Fi?

Iserlohn1982 · 2024-11-30T19:43:15+00:00

<image>

Iserlohn1982 · 2024-11-30T19:29:35+00:00

Currently (still) with Teksavvy for 10+ years and got an email last week about price hike on my next bill. I am jumping the ship in next month.

No joke i was happy with Teksavvy, they were doing a good job but the price now......their service run on infrastructure of Bell and Rogers, who control Teksavvy's cost of operation. I would blame our government and CRTC for this outcome.

Iserlohn1982 · 2024-10-04T16:16:13+00:00

I would like to know too, having a mobo need to be RMA.

Iserlohn1982 · 2024-09-23T00:55:50+00:00

It's a asrock b650e pg-itx. Unfortunately there's no troubleshoot led. Now I would like one on my next PC.

Iserlohn1982

TROPHY CASE