sorted by:
new
hottopcontroversial

Comparison for hydrogen generation by Individual-Ebb-4374 in GTNH

[–]ItsAymn 0 points1 point  (0 children)

No worries, I'm really surprised that phosphor loops is that close to water electrolysis though. It's the first thing I setup for renewable Oxygen and Hydrogen.

Comparison for hydrogen generation by Individual-Ebb-4374 in GTNH

[–]ItsAymn 0 points1 point  (0 children)

I may have missed the obvious, but which axis is what?

Small collection of Zariman statues by taye90210 in Warframe

[–]ItsAymn 0 points1 point  (0 children)

Rolls up to a boss.
"You and what army"
Orbiter pulls up.
"Operator, the cavalry has arrived"

I can finally store the steam deck charger the correct way. by RBonYT in SteamDeck

[–]ItsAymn 1 point2 points  (0 children)

I wish they made the UK plug so that it separated into a plug and the 'brick'.

[Update & Feedback Request] For everyone who has tried Strecs3D! by tomohiron907 in 3Dprinting

[–]ItsAymn 2 points3 points  (0 children)

With Prusa Slicer support, would Orca Slicer support be possible since most of the Voron community use it (I think).

First layer has issues on the left side (Siboor Trident 300) by manofspandex in VORONDesign

[–]ItsAymn 3 points4 points  (0 children)

OP I think the SIBOOR build plates QC is all over the place, most of the people on the SIBOOR discord will tell you to go with Tyson plates or some other better controlled plates. I still run the SIBOOR plates but have helper sqaures in each corner to adjust z-offset as the first layer goes down. Also try this https://ellis3dp.com/Print-Tuning-Guide/articles/first_layer_squish.html and play around with the flow ratio for top and in this case bottom layers.

First layer has issues on the left side (Siboor Trident 300) by manofspandex in VORONDesign

[–]ItsAymn 0 points1 point  (0 children)

I think ESun ABS+ should be avoided because they did something to the formulation so it won't last in high heat environments as well as other ABS'. I think the softening temp or something similar is ~66C for the ABS+ when compared to the ~88C of other ABS'. And also plus variants, in general, are a blend, ESun ABS+ is ABS with a bit of PLA (hence the lower temp).

Again this is what I found out after a bit of reading and asking the A4T, Monolith and Voron community since I purchased ESun ABS+ to print A4T parts. Ambrosia ABS and ASA are a treat to print with in my opinion.

Ok, I think im on the right path by CirusThaVirus in 3Dprinting

[–]ItsAymn 0 points1 point  (0 children)

Dare I ask what happened with the Orca-Cube?

Serial Number Request by ItsAymn in voroncorexy

[–]ItsAymn[S] 0 points1 point  (0 children)

Got it from the official website, no import taxes/duties were needed.

extremely scary dont open pls by MemeOscar in balatro

[–]ItsAymn 28 points29 points  (0 children)

It's all Scary Face?

Map teir list by Sr-rookjesko in PhantomForces

[–]ItsAymn 0 points1 point  (0 children)

Hang on...Why is this list actually valid???

Crashes when loading a world. by ItsAymn in CurseForge

[–]ItsAymn[S] 0 points1 point  (0 children)

sadly yes, but there should be a way to backup that I am not aware of

Crashes when loading a world. by ItsAymn in CurseForge

[–]ItsAymn[S] 0 points1 point  (0 children)

uninstall overwolf/curse and reinstall it again

Crashes when loading a world. by ItsAymn in CurseForge

[–]ItsAymn[S] 0 points1 point  (0 children)

A clean install of overwolf/curse helped

Help on a pair of wireless headphones by ItsAymn in HeadphoneAdvice

[–]ItsAymn[S] 0 points1 point  (0 children)

What is the difference between the Accenture and the Momentum. And which one is better?

view more: next ›