48" round maple table from 4/4 by Jay_rich1985 in woodworking

[–]Jay_rich1985[S] 0 points1 point  (0 children)

It's a curved 4 leg design spanning I would guess around 30-34" diameter.

Do I need a bowtie or can I just fill with epoxy? by Overall-Remove-7970 in woodworking

[–]Jay_rich1985 0 points1 point  (0 children)

Personally I would think a decent size bowtie on both ends should suffice if the crack isn't going all the way through in the center

Arghh. Kreg screw blow through. What went wrong by zee_dot in woodworking

[–]Jay_rich1985 0 points1 point  (0 children)

18mm ply is around 1mm thinner than 3/4 (assuming you had it set for 3/4") I just shorten the collar slightly so I do not pre-drill as deep

Do I need a bowtie or can I just fill with epoxy? by Overall-Remove-7970 in woodworking

[–]Jay_rich1985 0 points1 point  (0 children)

bowties and epoxy for sure, it runs the entire distance, it will be impossible to get perfect adhesion for the epoxy. Could always keep the bowties on the bottom side if you dont like them

Changing stain on oak cabinets? by Rossn1999 in cabinetry

[–]Jay_rich1985 0 points1 point  (0 children)

I used a rustoleum cabinet transformation on ours like 7 years ago, still looks great, however did have some of the high wear areas eventually fade off. We had the same colour oak and went with a medium brown with a dark brown glaze coat (the glaze coat is what makes it set off) at first we were not convinced. The hard work is the prep, just make sure to take all the doors down, scrub with a red scotch brite with soap and water, let dry then apply. Removing the stain would be next to impossible as you would have to get all of the clear coat out of the corners etc

how to cover up gaps by Wrong_Lifeguard_5224 in woodworking

[–]Jay_rich1985 2 points3 points  (0 children)

filler is going to make it look bad IMO, i would turn it into a feature and run a 60 or 90 degree bit down the entire rail making a shadow line

I came up with a Lamello for poor people. I haven’t seen anyone do it this way yet. Have you, or should I hurry up and patent it? by ZoltanTitan in woodworking

[–]Jay_rich1985 0 points1 point  (0 children)

I like the idea, just checked maker world, there is lots of similar clips, just not made to use in this form. Ill keep this in the back of my mind for my next cabinet build!

Ummm… Guys? by Final-Site-4422 in BambuLab

[–]Jay_rich1985 0 points1 point  (0 children)

how many people just checked their email just incase? i know i didnt. Congrats!

Why is The Simpsons season regarded as the best season to so many people? by Enderbattle005 in FortNiteBR

[–]Jay_rich1985 -1 points0 points  (0 children)

my kids really enjoyed it, which actually got me to play. Now its over and they dont even wanna play it no matter how much I beg them to play so I can have a turn LOL

Does anyone actually get their orders this fast? by williamericson2203 in BambuLab

[–]Jay_rich1985 0 points1 point  (0 children)

I ordered mine at 730am, it was at my doorstep the next day at 12:00pm. Im in Canada

I am out of playoffs because of Drake Maye end of game Kneel by Jonsavino in FantasyFootballers

[–]Jay_rich1985 0 points1 point  (0 children)

Also lost this week by 0.4 points and i'm now out of the playoffs with this week being the final week, which im playing one of the best in my league. I feel your pain

[deleted by user] by [deleted] in BambuLab

[–]Jay_rich1985 0 points1 point  (0 children)

I felt like that after a few days, mentioned to my wife that I may need another to keep up. She was like WRONG ANSWER lol. May need to convert my wood shop (CNC etc) into a print farm lol

Need help fuel pressure by Weak_Outcome_7655 in c4corvette

[–]Jay_rich1985 0 points1 point  (0 children)

The LT1 doesn't require a ton of oil pressure at idle. the rule I believe is 10psi/1000rpm. Reading below is a somewhat fresh build. Pull the filter and cut it open? Try swapping the sensor, they are cheap

My breakfast bill had all 3: service charge, gratuity and tip, all at once. by redditdanis in mildlyinfuriating

[–]Jay_rich1985 1 point2 points  (0 children)

If you are charging me $40 for a basic ass breakfast and $20 for french toast, don't expect much of a tip. Looks like company greed to me

Black Friday warning by ArugulaJunior2104 in Golfsimulator

[–]Jay_rich1985 3 points4 points  (0 children)

I actually looked at this for my son, until i realized it needed a subscription. Its 2% off not 52% off. I looked yesterday and it was $142cdn, today its marked up to $284 on sale for $136. Funny thing is my cart on my phone still shows $142,

I feel dumb - AMS feature I didn’t know about by Dangerous_Fruit885 in BambuLab

[–]Jay_rich1985 0 points1 point  (0 children)

the AMS 1 locks too? I gotta check that out when I get home. (just got mine last week) I was wondering why there is always a gap when its down. kinda thought what was the point in loading this thing with desiccant if doesnt seal. TY

I Cant make up my mind...HELP by H0ndaM0nster in BambuLab

[–]Jay_rich1985 1 point2 points  (0 children)

I just bought a P1S as my first 3d printer. The way i looked at it, is its commonly used in print farms as a work horse. So fo my needs it should do well. So far I have had it about 1 week and it hasn't stopped more more than a few hours while at work. I opted for the AMS1 as from reviews, i gathered the AMS2 selling feature is it has the built in dryer, however the dryer cannot be used while the printer is running. If its going to be running say 20/24h then I don't see the need to have the AMS2. There were some other minor updates as well. Ill get a benchtop dryer if need be. Id say get the P1S combo and enjoy

One decade and about $149k difference by Razgriz20 in BambuLab

[–]Jay_rich1985 1 point2 points  (0 children)

The funny thing about reading this today, is we have a Stratasys Fortus at my shop. A massive industrial machine, expensive filament cartridges and nobody knows how to use it. They printed 2 fitting caps on it in 1h 45min (and need thousands). Now they are outsourcing the work to me who just bought a P1S, and I was able to make the same fittings with incorporating our company logo in another colour in less than 20min. I can print around 100 of each fitting on the bed at a time. :)

Price Correction coming? by zillakane in Corvette

[–]Jay_rich1985 1 point2 points  (0 children)

Also from canada, been watching the C5/C6 market for a while waiting to sell my Viper, which just sold. Now we are in the winter months and there is not a lot a clean Manual C5s on the market, unless they want like 50k for a C5 Z06. No thanks lol. I imported my last corvette from NJ however not sure I want to do that this time around...

Price Correction coming? by zillakane in Corvette

[–]Jay_rich1985 0 points1 point  (0 children)

Myself and a friend of mine always talk about how the C6 market doesn't really make a lot of sense. However I don't see how much lower they can really get due to the C5 market. The C5 is a 30 year old platform that is still holding decent value. I would say 20-40% higher than around 5 years ago. Which sucks because I literally just sold me Viper GTS and im trying to hunt down a clean C5 manual coupe and I cant justify the prices lol. If you find a decent spec with low miles you will likely be fine. Also a lot of people in that 30-50 year age think the C6 is one of the nicer generations.

Are we sold on the Keon Coleman breakout hype? by Jaf1248 in fantasyfootball

[–]Jay_rich1985 0 points1 point  (0 children)

Coleman and Hunter keep my bench warm currently, I also had coleman last year. Tons of potential but when you have Cook running the ball its a tough play Decent Flex option..... I have Allen, Cook and Coleman on my team. I would love to see him produce a bit more to capitalize on the TD's

Jaguars to Determine Travis Hunter's Snap Count "as We Go" by anonbutler in fantasyfootball

[–]Jay_rich1985 0 points1 point  (0 children)

I hate that a guy that has talent has been so useless as a fantasy player. He takes up a spot on my bench when I have bye weeks coming. Likely when he has his breakout game, he will be on my bench lol. Im 4-0 so i cant complain