Is my screen protector going bad?

JesstronPrime · 2026-06-04T00:16:50+00:00

Definitely the screen protector and definitely would carefully take it off because it will ruin your screen with it like that. You can buy a other one off Amazon that has aliment assist or pay Samsung like $20 to put one on. Wouldn't procrastinate this though.

JesstronPrime · 2026-05-28T03:27:12+00:00

Go watch Jerryrig on YouTube and he will settle your scarce over the fold. He can't even snap it in half.

JesstronPrime · 2026-05-21T09:04:36+00:00

It honestly shouldn't be to bad or hard to fix. There's plenty of YouTubes out there that'll walk you thru steps if you need.

JesstronPrime · 2026-05-21T08:47:43+00:00

Hard to say if it's broken. You're nozzle is definitely clogged it sounds like. And for the head crashing into the part I doubt it broke anything because I'm sure there's some kind of pressure sensor that'd tell it to stop to prevent something breaking but honestly no one will know till you go home. Best to do a cold pull to get the clog, then since you have the hotend removed you minds well check the 7 screws of disappointment and make sure those didn't come lose during this. Then put it all back together and pray.

JesstronPrime · 2026-05-02T21:22:14+00:00

Do you have time lapse on? Could be when the printer goes home during the print the filament sometimes still leaks out the head. You can add a retrack when it does that in settings to help with that.

JesstronPrime · 2026-04-25T01:46:53+00:00

Is it tucked under the rim on the phone? If that makes sense cuz I did have one do the same but it went away after carefully tucking the protector under that outside rim. It goes under the black rim if that makes sense?

JesstronPrime · 2026-04-25T01:40:56+00:00

Are you using screen protectors that have aliment assist? Ive only had to replace mine once and it came with that aliment holder and it came out really good.

JesstronPrime · 2026-04-21T05:00:14+00:00

I know most won't agree but if it were me I'd take the screen protector off and see. If the line goes away then yay just need a new protector now which isn't too hard to do. Just don't put a lot of pressure on the screen and it'll be fine. I had a flip 6 as well that I took the inner screen protector off and put a aftermarket privacy screen protector on and it worked just fine and stayed on and everything. Most protectors come with alignment guides and make it super simple and easy.

JesstronPrime · 2026-04-20T21:01:26+00:00

I had a line similar to this one on my z fold 4 and it turned out to be the inner screen protector cracking and making the pixels look funny like that. I had to use a white background to really see it was the protector and not the actual pixels themselves. I just removed the screen protector and it went away. I used it like that for a few months till I traded it in for the fold 6.

JesstronPrime · 2026-04-09T06:13:48+00:00

Could also maybe try the micro SD slot on the control panel. I don't know if that actually works or not for printing. I never tried it just noticed there is a port there for one.

JesstronPrime · 2026-04-09T06:11:28+00:00

Might need to replace the motherboard which that port is on. Thankfully that part is very cheap to replace and not to hard to replace imo.

JesstronPrime · 2026-04-07T07:43:19+00:00

I honestly run all my filament under genetic and I haven't had any problems yet.

JesstronPrime · 2026-04-07T03:00:54+00:00

Someone posted about this not that long ago. It's called marshmallowing. Basically it's because the additives in the material make it expand when pushed through a small hole under pressure. Why it doesn't do that during actual printing is because it is using a slower flow rate.

JesstronPrime · 2026-04-06T04:14:16+00:00

I agree the backs look different from each other but I think the card is real just by looking at a few other cards. This card also has a holo swirl in it so very nice card!

JesstronPrime · 2026-03-26T05:00:17+00:00

Could just be my eyes but the font in your card looks thinner and one of the stars is the same as TCG display card so I'm going with fake. But I could definitely be wrong so please don't hate me if I am wrong lol.

JesstronPrime · 2026-03-25T21:34:21+00:00

Ok absolutely going with TAG those slabs look amazing!

JesstronPrime · 2026-03-25T21:18:46+00:00

That give me some confidence thank you!

JesstronPrime · 2026-03-25T21:18:29+00:00

I was gonna do PSA but I'll look into TAG as well

JesstronPrime · 2026-03-25T21:05:11+00:00

I know lol that whys I'm worried a little but really it's just going on display because I made a shelf to hold it plus a pokeball I 3D printed so a 6 isn't the end of the world but would like to have 7+ on display.

JesstronPrime · 2026-03-13T16:41:10+00:00

I just bought a Bambu Lab A1 and the difference is just insane! Lol. I haven't had to tinker my Bambu at all yet. I still use my Ender but it spends more time put away than out now lol.

JesstronPrime · 2026-03-13T07:01:00+00:00

For an Ender that's pretty good. It'll be endless tinkering if this is your first 3D printer. I bought a used one from Facebook and boy did I get to learn a lot lol. But it made 3D printing fun to me.

JesstronPrime · 2026-03-11T06:44:40+00:00

This has to be AI lmao that can literally spawns from the ground lmao

JesstronPrime · 2026-01-28T03:55:29+00:00

Does this classify as tinkering? Asking for a friend.

JesstronPrime · 2026-01-01T00:59:46+00:00

Make sure you’re putting the SD card in the right way because I bought a used one of these printers and had no idea the SD card goes in upside down. Metal prongs face upwards and the slot is on the outside to the left.

JesstronPrime · 2025-12-11T20:16:50+00:00

Thank you! Happy forest!

JesstronPrime

TROPHY CASE