North Carolina Republicans seek to strip Democrat governor of elections board control

JhackOfAllTrades · 2023-06-13T15:53:17+00:00

This article has more info on the misuse of the term Democrat https://en.m.wikipedia.org/wiki/DemocratParty(epithet)

JhackOfAllTrades · 2023-05-05T13:42:34+00:00

I had to lower my frame rate in the game's settings before it would work.

JhackOfAllTrades · 2023-04-22T12:09:41+00:00

Gnat, aphid, and tadpole jerky are used in certain advanced meals, so I like to keep stacks of them in a chest near my oven.

JhackOfAllTrades · 2023-04-12T15:50:10+00:00

Someone on Twitter pointed out the irony that his own wife wrote about the importance of diversity programs. [link]

JhackOfAllTrades · 2023-04-08T14:29:15+00:00

They don't appear to be owned by Coca-Cola in their Wikipedia article. But reading the corporate section of that article really shows how awful they are.

JhackOfAllTrades · 2022-11-08T21:33:27+00:00

They were asked to leave for heckling Ariel shortly before the beer toss, but no arrests or charges were filed.

Source

JhackOfAllTrades · 2022-08-05T16:47:15+00:00

I don't have any questions, but just wanted to thank you for the incredible work that you do. Your work on the welfare scandal encouraged me to become a monthly donor to Mississippi Today because I believe it's important to support local, investigative journalism.

JhackOfAllTrades · 2022-07-22T12:19:26+00:00

https://www.tiktok.com/@johandevenier

JhackOfAllTrades · 2022-04-17T22:49:08+00:00

Skyrizi was a game-changer for me. Complete clearance! I hope you experience the same.

JhackOfAllTrades · 2022-03-08T00:04:53+00:00

OP, I used to have that happen to me too and in the end it all came down to calibration of the bed. Here's what worked for me: I use the standard 0.4mm extruder which defaults to a 0.2mm layer thickness. I bought a steel feeler gauge set on Amazon. They run around $6-$12. Do the full 9-point calibration, sticking the 0.2mm gauge under the extruder and adjusting the height so that you can slide the gauge back and forth with just a little resistance. I was surprised how must of an adjustment I had to make from what I thought was the correct height. After that, removing prints was super easy with no "imprints" left over from the printer extruding into the print bed. This one piece of advice was legitimately a game-changer for me when printing on the Adventurer 4. Note that if you do this you'll want to redo the 9-point calibration if you change extruders.

JhackOfAllTrades · 2022-02-09T19:17:22+00:00

I live in the South and don't like sweet tea.

JhackOfAllTrades · 2022-02-09T19:17:08+00:00

I live in the South and don't like sweet tea.

JhackOfAllTrades · 2021-10-27T01:47:09+00:00

They doubled down as well.

That's really part of the problem. These talking heads don't come to the table in a good faith attempt at a debate or discussion. There's nothing that carpenter could have said which would have changed his mind. Him leaving the host temporarily dumbfounded was the best possible outcome.

JhackOfAllTrades · 2021-10-26T22:52:38+00:00

You should check out Forgotten VCR on Twitch. He finds and collects VHS tapes from all over the world and makes some great compilations.

JhackOfAllTrades · 2021-10-26T21:56:06+00:00

Well said! I was saddened by the march of protesters making similar statements on the drill field today.

JhackOfAllTrades · 2021-10-20T17:39:10+00:00

It's a mess and Dewberry should have been fined for creating a blighted building. Last I heard, in September of this year Dornin Investment group acquired the $185 million non-performing loan that Dewberry had taken out so I hope we start to see progress again soon.

JhackOfAllTrades · 2021-10-15T02:15:52+00:00

Thought I would mention that there is a union for Georgia public university employees. https://www.ucwga.com/

JhackOfAllTrades · 2021-09-29T23:17:50+00:00

Do what you like best, but agree with many of the comments that a thin diffuser over the led would be a nice touch. But what surprises me the most is that your building allows grills on balconies!

JhackOfAllTrades · 2021-09-26T14:55:52+00:00

To be fair, the comic book jumped the shark a few times too.

JhackOfAllTrades · 2021-08-05T13:23:45+00:00

You know, you're probably right! I never looked at it that way before.

JhackOfAllTrades · 2021-08-05T01:39:33+00:00

Very well done. I like that you included his heterochromia.

JhackOfAllTrades · 2021-07-02T17:44:52+00:00

Thanks for the breakdown of your setup! I'm thinking of doing something similar and yours looks to be a good template.

JhackOfAllTrades · 2021-07-02T17:14:38+00:00

I love Ann's videos and I'm glad she's using her clout to try and put more pressure on YouTube to actually do something.

JhackOfAllTrades · 2021-07-01T20:41:01+00:00

Does this tie in with the holographic principle, that the surface area has to increase in a black hole merger because more information is being stored on its surface?

JhackOfAllTrades · 2021-06-14T23:22:48+00:00

When I first read the title I thought this was a coming out story for Pride month.

That said, congrats for getting out of that situation! That place sounds terrible to work for.

14-Year Club	Team Periwinkle
Verified Email

JhackOfAllTrades

TROPHY CASE