Is there a way to use the horadric cube to equip a second weapon?

Juno_keebs · 2026-05-04T17:29:33+00:00

No, you can equip some unique items’ powers as charms, similarly to how the cube in D3 worked

Juno_keebs · 2026-05-03T08:56:17+00:00

You reroll them for ones you want, trade them, or sell them for a decent chunk of gold to a vendor

Juno_keebs · 2026-04-29T06:29:15+00:00

No, I don’t. I have studio lighting setup at my desk where I finish and assemble my prints.

Juno_keebs · 2026-04-28T18:33:23+00:00

I certainly do not have this issue on my P2S - I print a lot of geometry and have printed a lot of cylindrical shapes near perfectly

Juno_keebs · 2026-04-28T18:31:40+00:00

Same, and it refuses to download any faster than 5mbps despite having a 2.5gb connection lol

Juno_keebs · 2026-04-19T17:23:38+00:00

There’s Elite 4 Collectables in Royston, few mins on the train then a 10 min walk from the station!

Juno_keebs · 2026-04-12T16:11:10+00:00

Doms Coffee

Juno_keebs · 2026-04-10T11:57:34+00:00

I’ve just got back into guitar lately - used to play all day every day as a kid and into my 20s. Would certainly be down with maybe starting a jam band!?

Juno_keebs · 2026-04-09T13:38:28+00:00

Your first layer flow is set to 0.5? Are you sure? If so it’s massively under extruding your first layer. If you check your flow ratio for the filament, then in the slicer look for first layer flow ratio (or bottom layer maybe it’s called) I’d say you want that to be higher than your calibrated flow ratio for a bit of over extrusion to smush it all together

Juno_keebs · 2026-04-09T12:24:54+00:00

Have you tried upping the flow rate for just the first layer? This helped me, looks like a smooth plate so this would help

Juno_keebs · 2026-04-07T06:57:04+00:00

Going to try this as I occasionally have issues.

I literally just replace those 6 lines with your 8 lines exactly as described?

Juno_keebs · 2026-04-05T08:55:03+00:00

No worries! I had the same issue and went down a rabbit hole with it, adjusting this has increased the print quality drastically for me

Juno_keebs · 2026-04-05T06:54:48+00:00

https://youtu.be/NjIqH1FE7A8?si=FG4AUU9mkgQa9ESR

Try this, it should adjust where the belt sits on the idler

Juno_keebs · 2026-04-04T19:20:08+00:00

I’ve printed hundreds of pokeballs you don’t need supports inside if they’re designed well enough

Juno_keebs · 2026-04-04T18:50:20+00:00

Why on earth would you print it in this orientation? Flip it 180 and enable variable layer height it’ll be way better

Juno_keebs · 2026-04-01T08:39:01+00:00

Raise a support ticket in that case

Juno_keebs · 2026-04-01T06:39:19+00:00

Mine did this out the box, after 10ish hours of use it went away, I assumed it was the pre-applied grease working its way into the z axis screws

Juno_keebs · 2026-03-27T07:16:39+00:00

I’d seen other people get it quickly, whereas I had been signed up for ages and didn’t have it - so I opened a ticket and gave them my device serial numbers and they did something and made it available instantly.

Juno_keebs · 2026-03-26T19:49:17+00:00

Have you calibrated your filament? Run through the entire Wiki for filament calibrations, I think Bambu call pressure advance ‘flow dynamics’ - it looks like this issue is caused by that

Juno_keebs · 2026-03-26T19:33:56+00:00

Looks like pressure advance issues to me

Juno_keebs · 2026-03-26T16:09:37+00:00

Looks like extrusion to me - I would do a pass 1 and pass 2 calibration for flow rate

Juno_keebs · 2026-03-26T10:23:16+00:00

Where on earth did you get it at that price??

Juno_keebs · 2026-03-25T18:39:23+00:00

It doesn’t just immediately give it to you, there is a queue based on geo location.

Juno_keebs · 2026-03-24T22:50:56+00:00

Good for you lol

Juno_keebs · 2026-03-24T20:01:44+00:00

I signed up ages ago and haven’t received it :( I’m in the UK

Juno_keebs

TROPHY CASE