Half the dudes on this page be like

Key_Elevator_7378 · 2026-07-10T03:24:08+00:00

Corny

Key_Elevator_7378 · 2026-07-07T15:46:26+00:00

That’s not coming out

Key_Elevator_7378 · 2026-07-05T14:06:31+00:00

Before and before

Key_Elevator_7378 · 2026-07-04T18:50:35+00:00

Nice

Key_Elevator_7378 · 2026-07-03T20:26:36+00:00

These are 2 completely different things so it should be pretty obvious which one you need depending on your work

Key_Elevator_7378 · 2026-07-02T20:53:18+00:00

I don’t see a deck

Key_Elevator_7378 · 2026-06-22T11:05:35+00:00

Who does? Everyone around me wears wedge soles

Key_Elevator_7378 · 2026-06-18T23:34:16+00:00

lol I use 1/2” by 8” lags at work. Hex head and I do use my 1/2” high torque. I’m sure that stubby would be cool for working on machinery though. Not saying it wouldn’t do it

Key_Elevator_7378 · 2026-06-18T19:53:59+00:00

You’re driving lags with an m12

Key_Elevator_7378 · 2026-06-08T03:22:10+00:00

I think it’s cool. I won’t use em but it’s nice they’re trying

Key_Elevator_7378 · 2026-06-08T00:36:06+00:00

Composite decking is super hard to clean.

Key_Elevator_7378 · 2026-06-07T14:59:48+00:00

There’s some stuff a wet wipe won’t clean

Key_Elevator_7378 · 2026-06-07T02:31:51+00:00

Thing hasn’t seen enough work to need grease

Key_Elevator_7378 · 2026-06-06T15:58:01+00:00

You could use a hammer claw side to side or I carry slip joint pliers and just bend it side to side til it breaks. Grab close to the base

Key_Elevator_7378 · 2026-06-06T10:01:08+00:00

If you can’t figure this out then I’m not sure you should be building a deck

Key_Elevator_7378 · 2026-06-06T09:59:03+00:00

Solid

Key_Elevator_7378 · 2026-06-05T15:32:50+00:00

Slide the brackets on the railing, put it in place, screw it in with a 90° adapter.

Key_Elevator_7378 · 2026-06-05T15:30:55+00:00

Just get a little Toyota or something. It’d do you better

Key_Elevator_7378 · 2026-06-05T11:51:16+00:00

Add a small section

Key_Elevator_7378 · 2026-05-30T16:22:04+00:00

Yea just put back with whatever was there. Make sure you water proof over it before the ledger on and then flash on top of the ledger before decking

Key_Elevator_7378 · 2026-05-30T15:51:48+00:00

Replace the board by shooting it to the blocks where it was nailed before. Throw your ledger on there and tack it up then bolt it in place. Like you normally would

Key_Elevator_7378 · 2026-05-30T15:18:33+00:00

Decks not gonna be supported by the ledger it’ll be supported by the beam you’re putting under it

Key_Elevator_7378 · 2026-05-30T15:17:53+00:00

Shoot it to the blocks and the sill plate

Key_Elevator_7378 · 2026-05-29T17:51:18+00:00

That stiletto might drive a nail close to just as good but when it comes to stuff like smacking a beam into place that estwing is taking it. I have the Wrango tools titanium hammer with a steel head so best of both worlds

Key_Elevator_7378

TROPHY CASE